EZ-ACCESS PATHWAY HD Code Compliant Modular Access System Скачать руководство пользователя страница 75

Страница: 75 / 92

PATHWAY HD Code Compliant Modular Access System Installation Manual

Page 75 of 92

6.2.

SECURE RAMPS TO PLATFORMS

6.2.1.

Once installation of ramps, platforms, handrails, connectors, and closures are

complete and all fasteners and set screws have been tightened, secure ramps to

platforms with ramp end clips (included in RAMP HANGER PAIR).

Use two ramp end clips at all locations where ramps meet platforms.

6.2.2.

Position each ramp end clip with the hole pointing up and oriented as shown (FIG. 6.2),

then insert the short end of the ramp end clip into small gap between the ramp and the

platform in the area where the ramp side rail overlaps the ramp end tread.

6.2.3.

Before the ramp end clip contacts the ramp side rail, rotate the ramp end clip so the

short end extends into the recess under the ramp end tread (FIG. 6.2).

6.2.4.

Use the hole in the ramp end clip as a template to drill 1/8” pilot hole in the platform

side rail, and then use the 1/4” x 1” long self-drilling screws to secure the ramp end

clip to the platform side rail (FIG. 6.3).

6.2.5.

FIG. 6.4 shows the top view of the completed end clip installation.

6.2.6.

Repeat this process for all locations where a ramp meets a platform.

FIG. 6.2

FIG. 6.3

FIG. 6.4

Содержание PATHWAY HD Code Compliant Modular Access System





























































































Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY HD Code Compliant Modular Access System, Руководство по установке

Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды