EZ-ACCESS PATHWAY HD Code Compliant Modular Access System Скачать руководство пользователя

Страница: 37 / 92

PATHWAY HD Code Compliant Modular Access System Installation Manual

Page 37 of 92

5.2.5.

Attach the barrier attachment plate to the barrier using a 5/16”-18 x 1” long hex bolt

and 5/16” flat washer. Make sure the leg of the attachment plate with the two smaller

holes is captured under the upper hook and in contact with the ramp side rail.

5.2.6.

Move the ramp or platform slightly (if needed) and clamp the attachment plate to the

side rail before drilling (FIG. 5.4).

5.2.7.

Use the two smaller holes in the barrier attachment plate to drill two 1/4” or 9/32”

holes through the ramp side rail (FIG. 5.5).

5.2.8.

Connect the barrier attachment plate to the ramp side rail using 1/4”-20 x 3/4” long

ribbed neck carriage bolts, 1/4”-20 nylon insert locknuts, and 1/4” flat washers. Orient

the head of the carriage bolt on the ramp side as shown (FIG. 5.5).

5.2.9.

Tighten all fasteners securely.

FIG. 5.4

FIG. 5.5

Содержание PATHWAY HD Code Compliant Modular Access System





























































































Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY HD Code Compliant Modular Access System, Руководство по установке

Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды