EZ-ACCESS PATHWAY HD Code Compliant Modular Access System Скачать руководство пользователя

Страница: 12 / 92

PATHWAY HD Code Compliant Modular Access System Installation Manual

Page 12 of 92

2.2.6.

Lift each corner of the platform and install a foot on each support leg, oriented so that

the foot extends under the platform (FIG. 2.4).

If necessary due to site conditions, the feet can be oriented in other directions

but may present a tripping hazard if not oriented under the platform.

It is the installer’s responsibility to install the system in a manner which is safe for

the persons on and around the system and clearly mark any hazards created by

the installation.

2.2.7.

Make sure the feet are fully engaged on the legs and tighten the thumb screw on each

foot securely (FIG. 2.4.).

If installing on soft soil it may be necessary to set the foot on a concrete pad or

make other arrangements. Talk with your local contractor for additional

information.

2.2.8.

Use hole in the foot as a template to drill an 11/32” or 3/8” hole through each support

leg (FIG. 2.4).

2.2.9.

Insert a 5/16”-18 x 3” long hex bolt through the support leg and foot, then secure with

the 5/16”-18 nylon insert locknut.

2.2.10.

Adjust the final height of the platform by adjusting legs, one at a time, by loosening the

outer set screws in the platform corner pockets. Using a level, adjust the platform height

and re-tighten.

2.2.11.

Once the final height has been adjusted, tighten the second, outer lower set screw in

each platform corner pocket.

2.2.12.

Insert a plug and fully seat into the top of each support leg (FIG. 2.4). Use a rubber

mallet or similar tool to fully seat as needed. If necessary, use construction adhesive to

bond the plug in place.

2.2.13.

Tighten all set screws and fasteners securely.

2.3.

CONNECT TWO PLATFORMS TOGETHER

2.3.1.

Install the first platform as described in the previous steps except on the side where the

second platform will connect, install two CONNECTOR – PLATFORM TO PLATFORM

before installing feet onto the support legs.

Make sure the platform connector set screws are oriented outward so they will be

accessible.

Any two platforms of the same width can be connected. For example, two 5' x 5’ or

5’ x 6’ platforms are often connected to make a turn back platform.

2.3.2.

Slide platform connectors up until they contact the bottom of the platform (FIG. 2.5),

and then tighten set screws securely.

2.3.3.

Install a support leg stub into the open pocket in each connector until the bottom of the

stub is flush with the bottom of the connector, and then tighten set screws securely.

2.3.4.

Insert a plug and fully seat into the top of each support leg stub. Use a rubber mallet or

similar tool to fully seat as needed. If necessary, use construction adhesive to bond the

plug in place.

2.3.5.

Install the second platform as described in the previous section except only install

support legs, plugs, and feet on the opposite side of where the platforms will connect

(FIG. 2.6).

2.3.6.

Lift the second platform and slide the open corner pockets over the support leg stubs

extending up from the platform connectors.

2.3.7.

Tighten the set screws in the platform corner pockets securely.

2.3.8.

Adjust the platform heights and level as needed.

2.3.9.

Tighten all setscrews securely.

Содержание PATHWAY HD Code Compliant Modular Access System





























































































Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY HD Code Compliant Modular Access System, Руководство по установке

Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды