EZ-ACCESS PATHWAY HD Code Compliant Modular Access System Скачать руководство пользователя страница 60

Страница: 60 / 92

PATHWAY HD Code Compliant Modular Access System Installation Manual

Page 60 of 92

5.8.

TWO-LINE RAIL CORNER TURN

There are five special closures available for filling the space between two ramps in a corner turn

configuration: Two-Line Rail for a 5’ x 5’ platform, picketed guard for a 5’ x 5’ platform, two-line

rail for a 6’ x 6’ platform, picketed guard for a 6’ x 6’ platform, and special closure for 54” wide

ramps used on a 5’ platform side. Corner turn closures for a 5’ x 7’ and 5’ x 6’ platforms are

uncommon so must be ordered as customs for the specific configuration.

5.8.1.

Install the platform angle post (not already attached to the platform) in the open

platform corner pocket. Align the bottom of post with the bottom of corner pocket,

and then tighten the set screws securely. Refer to ‘HANDRAILS’ section for additional

details on securing the post to corner pocket.

5.8.2.

The barrier and mid rail of a two-line corner turn are installed in the same manner as a

two-line closure. Refer to ‘TWO-LINE RAIL BARRIER AND MID RAIL’ section and

complete the steps described to connect both frames to the platform angle post in

the corner. FIG. 5.36 shows this stage of the assembly.

FIG. 5.36

Содержание PATHWAY HD Code Compliant Modular Access System





























































































Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY HD Code Compliant Modular Access System, Руководство по установке

Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды