EZ-ACCESS PATHWAY HD Code Compliant Modular Access System Скачать руководство пользователя

Страница: 68 / 92

PATHWAY HD Code Compliant Modular Access System Installation Manual

Page 68 of 92

FIG. 5.47

5.10.4.

Insert a 2-15/16” ring joiner in one of the ramp

handrails at the corner turn, followed by an

adjustable elbow and another 2-15/16” ring

joiner. Orient the ring joiner set screws toward

the underside of handrail. Tighten ring joiner

set screws and adjustable elbow assembly

screw enough to hold components in place but

still allow them to rotate. Install 2-15/16” ring

joiners and adjustable elbow in the other ramp

handrail in the same manner (FIG. 5.47).

5.10.5.

Align the faces of the two closest 2-15/16” ring

joiners in the corner and measure gap between

the two parallel faces. Trim the 1-1/2” diameter

tube to measured length (FIG. 5.47).

5.10.6.

Using a metal file, remove sharp edges from

cutting.

5.10.7.

Install trimmed 1-1/2” diameter tube in gap

between the 2-15/16” ring joiners. Disassemble

and reassemble ring joiners and adjustable

elbows as needed to complete the installation

(FIG. 5.48).

5.10.8.

Insert 1-1/2” end plugs on all open ends of

frame top rails. Use a rubber mallet or similar

tool to fully seat as needed. If necessary, use

construction adhesive to bond plug in place.

5.10.9.

Tighten all fasteners securely, including all ring

joiner set screws and elbow assembly screws if

not completed previously.

FIG. 5.48

Содержание PATHWAY HD Code Compliant Modular Access System





























































































Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды

EZ-ACCESS PATHWAY HD Code Compliant Modular Access System, Руководство по установке

Результаты поиска

Содержание PATHWAY HD Code Compliant Modular Access System

Отзывы:

Похожие инструкции для PATHWAY HD Code Compliant Modular Access System

Бренды по названию

Популярные бренды