Extron electronics MVX VGA A Скачать руководство пользователя страница 28

Страница: 28 / 107

3-5

MVX VGA A Matrix Switchers • Operation

PRELIMINAR

View (

) button and/or LED —

The View (

) button and LED have two

primary functions (•) and six secondary functions (

❏

• Selects a

View-only

mode that displays the current configuration.

View-only

mode also provides a way to mute and unmute the outputs. See

“Muting and unmuting video and/or audio” on page 3-18.

• Indicates that

View-only

mode is active.

❏

Decreases the audio level of the selected input. See “Viewing and

adjusting the input audio level” on page 3-25.

❏

Indicates a negative (attenuation) audio level. See “Viewing and

adjusting the input audio level” on page 3-25.

❏

Decreases the volume of the selected output. See “Viewing and adjusting

the output volume” on page 3-30.

❏

With the Enter, Preset, and Esc buttons, selects

Serial Port Configuration

mode. See “Selecting the rear panel Remote port protocol and baud rate”

on page 3-38.

❏

Selects 38400 baud for the Remote port in

Serial Port Configuration

mode.

See “Selecting the rear panel Remote port protocol and baud rate” on

page 3-38.

❏

Indicates that the Remote port is set to 38400 baud in

Serial Port

Configuration

mode. See “Selecting the rear panel Remote port protocol

and baud rate” on page 3-38.

Esc (

) button and/or LED —

The Esc (

) button and LED have two primary

functions (•) and six secondary functions (

❏

• Cancels operations or selections in progress and resets the front panel

button indicators.

The Esc (

) button does

not

reset the current configuration, the RGBHV button

and Audio selection button, any presets, or any audio gain or attenuation

settings.

• Flashes once to indicate that the escape function has been activated.

❏

Increases the audio level of the selected input. See “Viewing and

adjusting the input audio level” on page 3-25.

❏

Indicates a positive (gain) audio level. See “Viewing and adjusting the

input audio level” on page 3-25.

❏

Increases the volume of the selected output. See “Viewing and adjusting

the output volume” on page 3-30.

❏

With the Enter, Preset, and View buttons, selects

Serial Port Configuration

mode. See “Selecting the rear panel Remote port protocol and baud rate”

on page 3-38.

❏

Selects 115200 baud for the Remote port in

Serial Port Configuration

mode.

See “Selecting the rear panel Remote port protocol and baud rate” on

page 3-38.

❏

Indicates that the Remote port is set to 115200 baud in

Serial Port

Configuration

mode. See “Selecting the rear panel Remote port protocol

and baud rate” on page 3-38.

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды