Extron electronics MVX VGA A Скачать руководство пользователя страница 83

Страница: 83 / 107

MVX VGA A Matrix Switchers • Matrix Software

5-2

Matrix Software

PRELIMINAR

Matrix Switchers Control Program

The Windows-based Extron Matrix Switchers Control Program communicates with

the switcher via the rear panel Remote RS-232/RS-422 port and the front panel

Configuration (RS-232) port to provides an easy way to set up ties and sets of ties.

The program is compatible with Windows 2000 and Windows XP. Updates to these

programs can be downloaded from the Extron Web site (http://www.extron.com).

Installing the software

The program is contained on the Extron Software Products CD-ROM, disk B.

Install the software as follows:

For full functionality, install both of the following programs:

• The Matrix Switchers Control Program

• The Firmware Loader

Insert the CD-ROM into the drive. The installation program should start

automatically. If it does not self-start, run Launch.exe from the CD.

The Extron software CD window appears (figure 5-1).

Figure 5-1 — Software CD window

Click the Software tab (figure 5-1).

Scroll to the desired program and click

Install

(figure 5-2).

Figure 5-2 — Software installation

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды