Extron electronics MVX VGA A Скачать руководство пользователя страница 29

Страница: 29 / 107

Operation, cont’d

MVX VGA A Matrix Switchers • Operation

3-6

PRELIMINAR

I/O controls

You must specify video, audio, or both when you are creating or viewing a

configuration. This is done with the RGBHV button (

) and Audio (

) buttons.

On some MVX switchers, the video selection button is labeled “Video” rather

than “RGBHV”.

RGBHV button and/or LED —

The RGBHV button and LED have two

primary functions (•) and five secondary functions (

❏

• Selects and deselects video for a configuration that is being created or

viewed.

• Lights amber to indicate that video is available for configuring or for

viewing.

❏

With the Enter button and Audio button, selects between front panel

locks (

Lock

mode 2 and

Lock

mode 0). See “Setting the front panel locks

(

Executive

modes)” on page 3-36.

❏

With the Audio button, selects between front panel locks (

Lock

mode 2

and

Lock

mode 1). See “Setting the front panel locks (

Executive

modes)”

on page 3-36.

❏

With the Audio button, initiates the front panel system reset. See

“Performing a system reset from the front panel” on page 3-37.

❏

Selects the RS-232 protocol for the Remote port in

Serial Port Configuration

mode. See “Selecting the rear panel Remote port protocol and baud rate”

on page 3-38.

❏

Indicates that the Remote port is set to the RS-232 protocol in

Serial Port

Configuration

mode. See “Selecting the rear panel Remote port protocol

and baud rate” on page 3-38.

Audio button and/or LED —

The Audio button and LED have two primary

functions (•) and six secondary functions (

❏

• Selects and deselects audio for a configuration that is being created or

viewed.

• Lights to indicate that audio is available for configuration or viewing.

❏

Selects the

Audio

mode, in which you can adjust the input audio level.

See “Viewing and adjusting the input audio level” on page 3-25.

❏

With the Enter button and RGBHV button, selects between front panel

locks (

Lock

mode 2 and

Lock

mode 0). See “Setting the front panel locks

(

Executive

modes)” on page 3-36.

❏

With the RGBHV button, selects between front panel locks (

Lock

mode 2

and

Lock

mode 1). See “Setting the front panel locks (

Executive

modes)”

on page 3-36.

❏

With the RGBHV button, initiates the front panel system reset.

See “Performing a system reset from the front panel” on page 3-37.

❏

Selects the RS-422 protocol for the Remote port in

Serial Port Configuration

mode. See “Selecting the rear panel Remote port protocol and baud rate”

on page 3-38.

❏

Indicates that the Remote port is set to the RS-422 protocol in

Serial Port

Configuration

mode. See “Selecting the rear panel Remote port protocol

and baud rate” on page 3-38.

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды