Extron electronics MVX VGA A Скачать руководство пользователя страница 45

Страница: 45 / 107

Operation, cont’d

MVX VGA A Matrix Switchers • Operation

3-22

PRELIMINAR

Example 6: Saving a preset

The following steps show an example in which the current configuration is saved as

a preset. The steps show the front panel indications that result from your actions.

Press and release the Esc button (figure 3-34).

ENTER PRESET VIEW

ESC

CONTROL

Press the Esc button to clear all selections.

The LED blinks once.

= LED blinks once.

Figure 3-34 — Clear all selections

Press and

hold

the Preset button for approximately 2 seconds until the Preset

LED blinks (figure 3-35).

PRESET

Press and

hold the Preset button until the

Preset LED blinks.

Release the
Preset button.

2 seconds

All input and output LEDs with assigned presets light.
If you then save the configuration to a lit preset number,
the configuration data at that preset location is overwritten.

Lit

(Preset Assigned)

Output
LEDs

Unlit

(Preset Unassigned)

= Blinking LED

Preset 13 Preset 14

Preset 16

Preset 15

Figure 3-35 — Enter

Save Preset

mode

Press and release the Output 1 button (figure 3-36).

ENTER PRESET VIEW

CONTROL

The Enter LED blinks to indicate
the need to save the preset.
The Preset LED continues to blink.

Press and release the Output 1 button.
The LED blinks to indicate that this

preset

number is selected but not saved.

= Blinking LED

Preset 13 Preset 14

Preset 16

Preset 15

Figure 3-36 — Select the preset

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды