Extron electronics MVX VGA A Скачать руководство пользователя страница 27

Страница: 27 / 107

Operation, cont’d

MVX VGA A Matrix Switchers • Operation

3-4

PRELIMINAR

Control buttons

Enter button and/or LED —

The Enter button and LED have three primary

functions (•) and four secondary functions (

❏

• Saves changes that you make on the front panel. To create a simple

configuration:



Specify RGBHV, audio, or both (see I/O selection buttons [

] and

[

]).



Press the desired input button (



Press the desired output button(s) (



Press the Enter button.

• Indicates that a potential tie has been created but not saved.
• Indicates that a global preset has been selected to be saved or recalled but

that the preset action has not been accomplished.

❏

With the Preset, View, and Esc buttons, selects

Serial Port Configuration

mode. See “Selecting the rear panel Remote port protocol and baud rate”

on page 3-38.

❏

Selects 9600 baud for the Remote port in

Serial Port Configuration

mode.

See “Selecting the rear panel Remote port protocol and baud rate” on

page 3-38.

❏

Indicates that the Remote port is set to 9600 baud in

Serial Port

Configuration

mode. See “Selecting the rear panel Remote port protocol

and baud rate” on page 3-38.

❏

With the RGBHV and Audio buttons, select front panel security lockout

mode 2 or toggle between mode 0 (unlocked) and mode 2. See “Setting

the front panel locks (

Executive

modes)” on page 3-36.

Preset button and/or LED —

The Preset button and LED have two primary

functions (•) and three secondary functions (

❏

•

Activates

Save Preset

mode to save a configuration as a preset and

Recall

Preset

mode to activate a previously-defined preset.

•

Blinks when

Save Preset

mode is active and lights steadily when

Recall

Preset

mode is active.

❏

With the Enter, View, and Esc buttons, selects

Serial Port Configuration

mode. See “Selecting the rear panel Remote port protocol and baud

rate” on page 3-38.

❏

Selects 19200 baud for the Remote port in

Serial Port Configuration

mode.

See “Selecting the rear panel Remote port protocol and baud rate” on

page 3-38.

❏

Indicates that the Remote port is set to 19200 baud in

Serial Port

Configuration

mode. See “Selecting the rear panel Remote port protocol

and baud rate” on page 3-38.

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды