Extron electronics MVX VGA A Скачать руководство пользователя страница 62

Страница: 62 / 107

3-39

MVX VGA A Matrix Switchers • Operation

PRELIMINAR

To change a value

, press and release the button that relates to the desired

value (figure 3-61).

ENTER PRESET VIEW

ESC

RGBHV AUDIO

CONTROL

I/O

Press and release the button(s) to configure the port as follows:
Baud rate:
Enter — 9600

Preset — 19200

View — 38400

Esc — 115200

Serial protocol:
RGBHV — RS-232

Audio — RS-422

The selected LEDs blink and the others remain lit.
In this example, the port is set to RS-422 at 38400 baud.

= Blinking LED

= Lit LED,

Figure 3-61 — RS-232/RS-422 and baud rate selection

Press and release an input or output button to exit

Serial Port Configuration

mode (figure 3-62).

ENTER PRESET VIEW

ESC

RGBHV AUDIO

CONTROL

I/O

All Control LEDs return to the unlit state.

Each I/O LED returns to its previous state.

Press and release an

input or output button.

Figure 3-62 — Exit

Serial Port Configuration

mode

The switcher requires some time to save the new serial port settings. Wait at

least 5 minutes before removing power from the switcher, or the settings may be
lost.

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды