Extron electronics MVX VGA A Скачать руководство пользователя страница 47

Страница: 47 / 107

Operation, cont’d

MVX VGA A Matrix Switchers • Operation

3-24

PRELIMINAR

Press and release the Output 1 button (figure 3-40).

ENTER PRESET VIEW

CONTROL

The Enter LED blinks to indicate
the need to recall the preset.
The Preset LED remains lit.

Press and release the Output 1 button.
The LED blinks to indicate that this

preset

number is selected but not recalled.

= Blinking LED

Preset 13 Preset 14

Preset 16

Preset 15

Figure 3-40 — Select the preset

Press and release the Enter button (figure 3-41). The configuration stored in

memory location 13 (MVX 128 VGA A) or location 17 (MVX 1212 VGA A,

MVX 168 VGA A, MVX 1616 VGA A) is now the current configuration and can

be viewed in the

View-only

mode (see example 4, earlier in this chapter).

ENTER PRESET VIEW

ESC

CONTROL

The Enter and Preset LEDs
return to the unlit state.

Press the Enter button to
recall the preset.

All

input LEDs

return to the
unlit state.

Figure 3-41 — Press the Enter button

Содержание MVX VGA A












































































































Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды

Extron electronics MVX VGA A, Руководство пользователя

Результаты поиска

Содержание MVX VGA A

Отзывы:

Похожие инструкции для MVX VGA A

Бренды по названию

Популярные бренды