background image

 

Curtiss-Wright | GSM Series      Rev. U      PN29959      3/28/17 

 

 

1.0 INTRODUCTION 
1.1 Warranty and Limitation of Liability 

Products are warranted for two years from date of manufacture as determined by the serial 

number on the product label. Labels are generated and applied to the product at the time of 
shipment. The first and second digits are the year and the third and fourth digits represent the 
manufacturing week. Product repairs are warranted for 90 days from the date of the repair. The 
date of repair is recorded within 

Exlar’s database tracked by individual product serial number. 

Exlar Corporation warrants its product(s) to the original purchaser and in the case of original 

equipment manufacturers, to their original customer to be free from defects in material and 
workmanship and to be made only in accordance with Exlar's standard published catalog 
specifications for the product(s) as published at the time of purchase. Warranty or performance to 
any other specifications is not covered by this warranty unless otherwise agreed to in writing by 
Exlar and documented as part of any and all contracts, including but not limited to purchase 
orders, sales orders, order confirmations, purchase contracts and purchase agreements. In no 
event shall Exlar be liable or have any responsibility under such warranty if the product(s) has 
been improperly stored, installed, used or maintained, or if Buyer has permitted any unauthorized 
modifications, adjustments and/or repairs to such product(s). Seller's obligation hereunder is 
limited solely to repairing or replacing (at its opinion), at the factory any product(s), or parts 
thereof, which prove to Seller's satisfaction to be defective as a result of defective materials, or 
workmanship and within the period of time, in accordance with the Seller's stated product 
warranty (see Terms and Conditions above), provided, however, that written notice of claimed 
defects shall have been given to Exlar within thirty (30) days from the date of any such defect is 
first discovered. The product(s) claimed to be defective must be returned to Exlar, transportation 
prepaid by Buyer, with written specification of the claimed defect. Evidence acceptable to Exlar 
must be furnished that the claimed defects were not caused by misuse, abuse, or neglect by 
anyone other than Exlar. 

Components such as seals, wipers, bearings, brakes, bushings, gears, splines, and roller 

screw parts are considered wear parts and must be inspected and serviced on a regular basis. 
Any damage caused by failure to properly lubricate Exlar products and/or to replace wear parts at 
appropriate times, is not covered by this warranty. Any damage due to excessive loading is not 
covered by this warranty. 

The use of products or components under load such that they reach the end of their expected 

life is a normal characteristic of the application of mechanical products. Reaching the end of a 
product’s expected life does not indicate any defect in material or workmanship and is not 
covered by this warranty. 

Costs for shipment of units returned to the factory for warranty repairs are the responsibility of 

the owner of the product. Exlar will return ship all warranty repairs or replacements via UPS 
Ground at no cost to the customer. 

For international customers, Exlar will return ship warranty repairs or replacements via UPS 

Expedited Service and cover the associated shipping costs. Any VAT or local country taxes are 
the responsibility of the owner of the product. 

The foregoing warranty is in lieu of all other warranties (except as Title), whether expressed or 

implied, including without limitation, any warranty of merchantability, or of fitness for any particular 
purpose, other than as expressly set forth and to the extent specified herein, and is in lieu of all 
other obligations or liabilities on the part of Exlar. 

Seller's maximum liability with respect to these terms and conditions and any resulting sale, 

arising from any cause whatsoever, including without limitation, breach of contract or negligence, 
shall not exceed the price specified herein of the product(s) giving rise to the claim, and in no 
event shall Exlar be liable under this warranty otherwise for special, incidental or consequential 
damages, whether similar or dissimilar, of any nature arising or resulting from the purchase, 
installation, removal, repair, operation, use or breakdown of the product(s) or any other cause 
whatsoever, including negligence. 

The foregoing warranty shall also apply to products or parts which have been repaired or 

replaced pursuant to such warranty, and within the period of time, in accordance with Seller's 
stated warranty. 

NO PERSON INCLUDING ANY AGENT OR REPRESENTATIVE OF EXLAR IS 

AUTHORIZED TO MAKE ANY REPRESENTATION OR WARRANTY ON BEHALF OF EXLAR 
CONCERNING ANY PRODUCTS MANUFACTURED BY EXLAR, EXCEPT TO REFER 
PURCHASERS TO THIS WARRANTY

  

Содержание GSM20




































Отзывы: