Evoqua WALLACE & TIERNAN DEPOLOX 5 E страница 54 Скачать руководство пользователя

Страница: 54 / 92

WT.050.810.040.DE.IM.0817

Installation

DEPOLOX

5 E flow cell

Insert or screw the prepared sensors into the corresponding
mounting hole in the cell body cover.

3-electrode measuring cell (already installed)

Membrane sensor for total chlorine TC2 CAN or TC2-S CAN

C Conductivity sensor
D Redox combined measuring and reference electrode
E

LED glow stick

pH combined measuring and reference electrode

4.4.15

Installing calibration aids

Two calibration clips are installed in the housing cover. These are
inserted on the side at the back of the main housing.

The clips with plastic inserts for sensor is pushed into the upper
catch (A).

The second holding bracket holds the calibration solution in a bag
or cup. For the solution in the bag, position the holding bracket in
the upper position of the lower holding device (B). For the cup, use
the lower position (C).

Figure 16 Rear of DEPOLOX

5 E flow cell, pressurized

Upper holding device

Position of holding device for bag

C Position of holding device for cup

Figure 14 Non-pressurized

version

Figure 15 Pressurized ver-

sion

A C

F E D

Содержание WALLACE & TIERNAN DEPOLOX 5 E





























































































Результаты поиска

Содержание WALLACE & TIERNAN DEPOLOX 5 E

Отзывы:

Похожие инструкции для WALLACE & TIERNAN DEPOLOX 5 E

Бренды по названию

Популярные бренды

Evoqua WALLACE & TIERNAN DEPOLOX 5 E, Инструкция по эксплуатации

Результаты поиска

Содержание WALLACE & TIERNAN DEPOLOX 5 E

Отзывы:

Похожие инструкции для WALLACE & TIERNAN DEPOLOX 5 E

Бренды по названию

Популярные бренды