EUCHNER 099265 Скачать руководство пользователя страница 13

Страница: 13 / 38

Manual EKS Ethernet TCP/IP

2547185-01-10/22

Subject to technical modifications

Page 13/38

4.4 Technical data for compact version

Attention!

All the electrical connections must either be isolated from the mains supply by a safety transformer

according to EN IEC 61558-2-6 with limited output voltage in the event of a fault, or by other equivalent

isolation measures.

General parameters

Value

Unit

min.

typ.

max.

Housing

Plastic (PA 6 GF30, gray)

Degree of protection

IP65/IP67 in installed state

Ambient temperature at UB = DC 24 V

+ 55

°C

Mounting cut-out acc. to DIN IEC 61554

33 x 68

Power supply connection

Plug-in connection terminal, 3-pin, with screw terminal

(tightening torque 0.22 Nm),

conductor cross-section 0.14 ... 1.5 mm²

Operating voltage U

(regulated, residual ripple < 5 %)

DC V

Current consumption I

150

Interface, data transfer

Interface to the control system

Industrial Ethernet (IEEE 802.3)

Transfer protocol

TCP/IP

Data transfer rate (full duplex)

10/100

Mbit/s

Connection for Ethernet interface

1 x RJ45 socket

Data line

2 x 2 twisted-pair copper cables, screened; min. category 5

Cable length

100

LED indicator

Green: “Ready” (in operation)

Yellow: “Electronic-Key active” *

Red: “Fault”

Version

FSA

(For Safety Applications) – parameters for floating semiconductor switching contacts LA and LB

Switching contact connection

Plug-in connection terminal, 4-pin, with screw terminal

(tightening torque 0.22 Nm),

conductor cross-section 0.14 ... 1.5 mm²

Power supply U for load (LA, LB)

Switching current (with overload protection)

Output voltage U

(LA, LB) in switched state

U x 0.9

Resistance in switched state

ohms

Max. capacitive load

µF

Utilization category acc. to AC-12

EN IEC 60947-5-2 AC-15

DC-12

DC-13

50 mA / 24 V

Difference time of the outputs** (LB first)

200

Reliability values acc. to EN ISO 13849-1 (

FSA

version only)

Category (with downstream safe evaluation)

MTTF

Evaluation of data channel and one

switching contact LA

416

years

Evaluation of data channel and both

switching contacts LA and LB

803

years

* The LED illuminates yellow if there is a functional Electronic-Key in the Electronic-Key adapter.

** If the Ethernet interface is accessed during placement or removal of the Electronic-Key,

the difference time can be more than 200 ms.

Содержание 099265







































Результаты поиска

Содержание 099265

Отзывы:

EUCHNER 099265, Руководство пользователя, Страница: 13 / 38

Результаты поиска

Содержание 099265

Отзывы: