Estate Swing E-S 1000H Series Скачать руководство пользователя

Страница: 57 / 57

E-S 1000H Series Instruction Manual

Accessories Wiring

6.1

Photo Eye, Safety Edge, Safety Loop:



Normally Closed (NC) of safety device

Photo terminal of PHOTO block on gate opener

control board.



Common (COM) or Ground (GND) of safety device

GND terminal of PHOTO block on

gate opener control board.



12V Power positive (+) or (12V) or (PWR) of safety device

V+ terminal of PHOTO block

on gate opener control board.



12V Power Negative (-) or (GND) or (PWR) of safety device

GND terminal of PHOTO

block on gate opener control board.

*Remove safety jumper from PHOTO terminal if using a safety device.

Solenoid Gate Lock:



Positive Lead of lock

A terminal of E_LOCK block on gate opener control board.



Negative Lead of lock

B terminal of E_LOCK block on gate opener control board

Magnetic Gate Lock: Magnetic gate locks must have their own power supply and their own
relay.



Coil of relay for magnetic lock

A terminal of E_LOCK block on gate opener control

board.



Coil of relay for magnetic lock

B terminal of E_LOCK block on gate opener control

board.

Connect positive lead of the power supply directly to the positive lead of the mag lock.

Connect negative lead of the power supply to the N/C terminal of the relay.

Connect the COM terminal of the relay to the negative lead of the mag lock.

Содержание E-S 1000H Series


























































Результаты поиска

Содержание E-S 1000H Series

Отзывы:

Похожие инструкции для E-S 1000H Series

Бренды по названию

Популярные бренды

Estate Swing E-S 1000H Series, Инструкция по эксплуатации

Результаты поиска

Содержание E-S 1000H Series

Отзывы:

Похожие инструкции для E-S 1000H Series

Бренды по названию

Популярные бренды