Essilor PRO-E 600 Скачать руководство пользователя страница 21

Страница: 21 / 112

Bevel distribution value

Distribution value modifiable for:

◦

front/rear surface tracking

◦

a distributed bevel

◦

lens curve tracking

Modify the selected value

Reduce or increase the distribution value.

Bevel trajectory

Flat representation of the lens making it possible to assess the distances between the bevel crest and the

front & rear surfaces of the lens.

Trajectory modification

◦

General modification of the bevel curve

◦

Modification of the bevel curve at a particular point

◦

Displacement of the bevel curve

10.

Navigation

◦

Stop the cycle

◦

Back to the main edging screen

◦

Start the edging cycle

c. Customized beveling

The use of the customized bevel depends on 2 parameters: the frame and the lens. Before starting your job,

identify the major constraint.

EVEL

RAME

ENS

DVANTAGES

Classic

Lens for which the front surface

base is approximately equal to

the frame base.

Makes it possible to do an aesthetically pleasing

job. The lens material does not protrude beyond

the front of the frame.

Classic

Lenticular lens

, Executive lens

Makes it possible to do a job with specific lenses.

Classic

Thin lens

Makes it possible to balance out the bevel when

thin lenses are used.

Flat base

High base

Thin lens for which the front

surface base is approximately

equal to the frame base.

Makes it possible to retrieve the frame base in a

pattern tracing (base = 0).

Particular groove

(groove with

meniscus

)

Thin lens for which the base is

approximately equal to the

meniscus of the groove.

Compliance with original shape.

Job using a specific frame.

Pro-E 600 > v1 -02.17

SER

ANUAL

> II. E

DGING

LENS

Содержание PRO-E 600

















































































































Результаты поиска

Содержание PRO-E 600

Отзывы:

Бренды по названию

Популярные бренды

Essilor PRO-E 600, Руководство пользователя

Результаты поиска

Содержание PRO-E 600

Отзывы:

Бренды по названию

Популярные бренды