Essilor Pro-E 600 edger Скачать руководство пользователя

Страница: 40 / 198

4. P

ERFORM

TEP

BEVEL

A step bevel is strongly recommended for a high-base sports frame or a safety frame.

The step bevel finishing is active and available only if the tool is installed on the “small tools” module

(

p.168)

For more information, refer to the section Maintenance servicing> Changing edger tools > Installing

the Step ++ wheel

(

p.168)

This section describes the procedures for the creation of a step bevel:

◦

description of the Step bevel screens

(

p.41)

◦

perform a Step bevel in “automatic trajectory” mode

(

p.44)

or “front surface tracking” mode.

(

p.46)

The use of the step bevel is determined by two parameters: frame and lens.

•

Concerning the lens, the main constraint is the thickness of the nasal and temporal edges.

•

Concerning the frame, the crucial elements are the bridge and shape of the groove. The hinge is an
additional factor in the case of a metal frame, the arms for a plastic frame.

For this job, the lens base must always match the frame base perfectly. Too great a difference

between the two could be detrimental to the quality of your job.

Cross-section of a step bevel

1: Value of shelf bevel of rear surface

2: Width of the flat side of the bevel

3. Front surface tracking value

Pro-E 600_Pro-E 700 > v1 -10.18

SER

ANUAL

> II. E

DGING

LENS

Содержание Pro-E 600 edger







































































































































































































Результаты поиска

Содержание Pro-E 600 edger

Отзывы:

Похожие инструкции для Pro-E 600 edger

Бренды по названию

Популярные бренды

Essilor Pro-E 600 edger, Руководство пользователя

Результаты поиска

Содержание Pro-E 600 edger

Отзывы:

Похожие инструкции для Pro-E 600 edger

Бренды по названию

Популярные бренды