Erskine Attachments 420855 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

Erskine Attachments 420855 Скачать руководство пользователя страница 17

17

Carbide Tooth Maintenance



Avoid hitting stones and other hard objects,

especially  during  the  first  few  hours  of  use  with
new  teeth.    New  teeth  are  razor  sharp  and  more
prone  to  chipping  when  hitting  hard  objects.
Once  the  edges  have  worn  slightly,  they  will  be
less prone to chipping.



Teeth near the outer edge of the wheel will wear

more quickly than teeth near the center of the
wheel.



Check teeth for damage or wear every 2 hours of

use. Replace individual teeth as necessary using
only genuine Erskine

TM

replacement teeth.

Carbide Tooth Replacement

Always wear safety glasses when

performing this operation. Hardened tools can
shatter causing injury.

1. With the tractor parked, parking brake engaged,

PTO disengaged, engine off, stump grinder frame
resting on the ground, and stump grinder arm
supported by safety jacks, inspect the cutting
teeth for damage and wear.

2. To replace a tooth, remove the lock nut from the

threaded portion of the tooth and remove the
tooth from the cutting wheel.

3. Remove any dirt or debris from the pocket where

the old tooth was removed.

4. Insert the new tooth into the hole so that it sits in

the pocket of the cutting wheel facing in the same
direction as the other teeth.

IMPORTANT:

Be sure all teeth are pointed with

the cutting tip facing the direction that the arrows
in the cutting wheel point.

5. Holding the new tooth in the pocket, install a new

lock nut on the threaded portion of the tooth.

IMPORTANT:

Always use a new lock nut when

installing a new tooth on the cutting wheel.

ROUTINE MAINTENANCE

«
...
15
16
17
18
19
...
»

Содержание 420855

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды