manualshive.com logo in svg

Erskine Attachments 420855, Руководство оператора

Поделиться
Скачать
Erskine Attachments 420855 Скачать руководство пользователя страница 13

 

13 

 

                                  UNHOOKING THE STUMP GRINDER   

 

 

 

                   

 
   Use the following procedure to unhook and store the stump grinder when not in use. 

1.  Park the tractor and stump grinder on a solid, level 

surface and lower  the 3pt  arms so that the  stump 
grinder frame sits on the ground. 
 
 

2.  Turn off the engine and engage the parking brake. 

 
 

3.  Remove  the  retaining  pin  form  the  parking  stand, 

flip  the  parking  stand  to  the  parking  position,  and 
reinsert the pin. 

 
 

4. 

Return to the tractor’s operator’s seat and start the 
engine. 

 
 

5.  Using  the  auxiliary  hydraulics,  slowly  lower  the 

cutting  wheel  until  the  parking  stand  rests  on  the 
ground and tension is taken off of the top link pin. 

 
 

6.  Turn  off  the  engine  and  disconnect  the  stump 

grinder hydraulic couplers from the tractor. 

 
 

7.  Unhook  the  driveline  from  the  tractor  PTO  by 

compressing the quick release pin on the driveline 
yoke and sliding the driveline off of the PTO shaft. 

 
 

8.  Disconnect the upper and lower 3pt links from the 

stump grinder. 

 
 

9.  With  everything  disconnected,  return  to  the 

tractor’s  operator’s  seat,  start  the  engine,  and 
slowly  drive  the  tractor  forward  away  from  the 
stump  grinder  until  certain  that  every  part  of  the 
tractor is clear of the attachment. 

 
 

10. When  storing  for  a  long  period  of  time  (end  of 

season),  store  the  stump  grinder  in  a  dry  place 
with  the  driveline  off  of  the  ground.    Clean  the 
stump  grinder  thoroughly  and  repair/replace  any 
damaged  or  worn  parts  or  paint.    This  will  help 
ensure  that  the  stump  grinder  will  be  in  the  best 
working condition the next time it is used. 

Содержание 420855

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды