Erskine Attachments 420855 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

Erskine Attachments 420855 Скачать руководство пользователя страница 10

10

IMPORTANT:

Prior to operation, remove any

obstructions such as rocks or branches from the work
area that might be picked up and thrown. Avoid
contact between the cutting wheel and metallic
objects, rocks, and other objects harder than a stump.

1. With the operator in the seat of the tractor and the

seat belt fastened, start the engine.

2. Using the auxiliary hydraulics, raise the cutting

wheel.

3. Stop the engine and engage the parking brake.

4. Remove the retaining pin from the parking stand,

flip the parking stand to the operating position,
and reinsert the pin.

5. Return to the seat of the tractor, fasten seatbelt,

and start the engine.

6. Raise the 3pt arms to lift the attachment off of the

ground.

7. Position the tractor so that the stump grinder

cutting wheel is above the stump and the cut will
be made on the side of the stump nearest to the
tractor. Lower the stump grinder so that the
frame rests on the ground, and engage the tractor
parking brake.

To avoid serious injury or death

due  to  rollover,  NEVER  position  the  tractor
sideways  on  a  hill.  If  a  stump  is  on  a  hill,
position the tractor on the downhill side of the
stump.

8. With the engine RPM at an

idle

, engage the

tractor PTO. Gradually throttle the engine up to
operating RPM.

IMPORTANT:

Do not engage or disengage PTO

at full throttle.

IMPORTANT:

Do not engage PTO with stump

grinder frame raised off of the ground.

9. Using the tractor auxiliary hydraulic controls,

swing the cutting wheel to the far right side
(looking back at stump) and lower it to where it
will make a 3 to 6 inch cut.

OPERATING INSTRUCTIONS

First Pass

«
...
8
9
10
11
12
...
»

Содержание 420855

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды