Epson SureColor F7170 Скачать руководство пользователя страница 44

Страница: 44 / 188

Basic Operations

See “Saving Settings” on page 66.

1. Select an option.

To print with current settings:

Use the

buttons to select

Keep Settings Above

and press the

button.

Proceed to step 6.

To change settings:

Use the

buttons to select

Change Settings

and press the

button.

2. Select the items you want to change and press the

button.

3. Select the desired option and press the

button.

4. Press the

button to display the dialog shown in step 2 and then press the

button

again.

5. After confirming that the settings are correct, use the

buttons to select

Keep

Settings Above

and press the

button.

6. The roll type selection screen appears.

Use the

buttons to select the roll type that matches the loaded roll and press the

button.

7. If

is selected for

Remaining Setup

, you will be prompted to enter the length of the

current media. Use the

buttons to choose a length between 5.0 and 999.5 m (15

and 3000 feet) and press the

button. You can set in 0.5 m increments. If the display

is in feet, lengths are given in increments of 1 foot.

The printer will display

Ready

after a brief pause, showing that it is ready to print. Transmit

the data to be printed from the computer.

Содержание SureColor F7170





























































































































































































Результаты поиска

Содержание SureColor F7170

Отзывы:

Похожие инструкции для SureColor F7170

Бренды по названию

Популярные бренды

Epson SureColor F7170, Руководство пользователя

Результаты поиска

Содержание SureColor F7170

Отзывы:

Похожие инструкции для SureColor F7170

Бренды по названию

Популярные бренды