Epson SureColor F7170 Скачать руководство пользователя страница 79

Страница: 79 / 188

Basic Operations

Performing Feed Adjustment During Printing

Feed adjustment during printing is recommended for minor banding issues.

1. Press the

button during printing.

2. An adjustment value will be displayed. Use the

buttons to select a value.

If the feed amount is too small, black bands (dark stripes) will appear; adjust the feed
amount upwards.

If, in contrast, the feed amount is too large, white bands (pale stripes) will appear; adjust
the feed amount downwards.

3. If you are not satisfied with the results, use the

buttons to enter an adjustment

value.

The Feed Adjustment value of the currently selected media setting is overwritten.

4. Press the

button when settings are complete.

Содержание SureColor F7170





























































































































































































Результаты поиска

Содержание SureColor F7170

Отзывы:

Похожие инструкции для SureColor F7170

Бренды по названию

Популярные бренды

Epson SureColor F7170, Руководство пользователя

Результаты поиска

Содержание SureColor F7170

Отзывы:

Похожие инструкции для SureColor F7170

Бренды по названию

Популярные бренды