Epson SureColor F7170 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 188

background image

Maintenance

104

Chip Unit Replacement and Ink Refills

Time Period for Chip Unit Replacements and Ink Refills

If the message

Chip unit expended

is displayed on the control panel, this means that the

chip unit needs to be replaced soon. Obtain an ink pack of the appropriate color as soon
as possible.

You will be unable to print if the chip unit for even one color needs to be replaced. If the

Chip unit expended

message is displayed during a print job, you can replace the chip unit

and refill the ink while printing continues.

For information on compatible ink packs, see “Options and Consumable Products” on
page 162.

Be sure to read the Safety Data Sheet before a replacement procedure. You can download
it at your local Epson website.

Important:

This printer has a remaining ink warning system. Use the following procedure for replacement
and ink refills to replace the chip unit and refill the ink correctly.

After the service engineer attaches the ink tank, replace the chip unit and refill the ink when
remaining ink is about 70 mm (2.8 inches) from the bottom of the ink tank.

This system does not directly detect the amount of ink remaining in the ink tank. Instead, the
amount of ink remaining is estimated based on the ink usage conditions and displayed as a
message. To maintain the accuracy of this system, you must replace the chip unit and refill the
ink as soon as possible once the remaining ink is 70 mm (2.8 inches) or less from the bottom of
the ink tank.

«
...
102
103
104
105
106
...
»

Содержание SureColor F7170





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SureColor F7170

Бренд: D-Link Страницы: 38

Epress EtherNetwork DP-301P+

Бренд: D-Link Страницы: 2

Бренд: Oce Страницы: 255

Бренд: QMS Страницы: 26

Бренд: Oki Страницы: 28

Бренд: Ricoh Страницы: 278

Бренд: Mitsubishi Страницы: 86

Бренд: Objet Страницы: 122

Бренд: Anyload Страницы: 12

Бренд: Go Страницы: 3

LaserPro X500 III-80Y

Бренд: GCC Technologies Страницы: 127

Бренд: SINTERIT Страницы: 16

Бренд: Plas-Ties Страницы: 18

Бренд: MostFun Страницы: 25

Artisan 810 Series

Бренд: Epson Страницы: 36

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 68

Artisan 810 Series

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды