Epson SureColor F7170 Скачать руководство пользователя страница 100

Страница: 100 / 188

Maintenance

100

3. Insert the waste ink tube into the mouth of the new waste ink bottle and place the waste

ink bottle in the holder.

Tightly seal the lid on the used waste ink bottle.

4. Lower the stopper.

5. Press the

button.

6. Check again to confirm that a fresh waste ink bottle is correctly placed and then press

the

button to reset the waste ink counter.

Note:

If the underside of the stopper is stained, wipe it.

Important:

❏

Be sure to confirm that the waste ink tube is inserted in the mouth of the waste ink
bottle. Ink will spill onto the surrounding area if the tube is not inserted in the bottle.

❏

You will need the lid for the waste ink bottle when disposing of waste ink. Keep the lid
in a safe place; do not throw it out.

Important:

Confirm that the stopper adheres closely to the mouth of the bottle. If there is a gap, waste
ink may splatter and stain the surrounding area.

Содержание SureColor F7170





























































































































































































Результаты поиска

Содержание SureColor F7170

Отзывы:

Похожие инструкции для SureColor F7170

Бренды по названию

Популярные бренды

Epson SureColor F7170, Руководство пользователя

Результаты поиска

Содержание SureColor F7170

Отзывы:

Похожие инструкции для SureColor F7170

Бренды по названию

Популярные бренды