manualshive.com logo in svg

Epson Stylus COLOR 3000, Руководство по обслуживанию, Страница: 86 / 180

Поделиться
Скачать
Epson Stylus COLOR 3000 Скачать руководство пользователя страница 86

EPSON Stylus COLOR 3000

Rev. A

3-17

3.2.11  Printer Mechanism Disassembly

Section 3.2.11.1 thorough to Section 3.2.11.18 describe procedures for printer mechanism unit
disassembly.

3.2.11.1  CR Motor Removal

1.  Remove the printer mechanism unit. (See Section 3.2.6.)
2.  Dismount the belt tension spring to loosen the timing belt.
3.  Remove the timing belt from the pulley on the CR motor.
4.  Release the joint for the CR motor and base frame assembly by turning the motor counterclockwise in

the order shown by the steps 1 to 3 in Figure 3-13. Then remove the CR motor by pulling it toward the
bottom edge of the base frame assembly.

CAUTION

CR motor fan and CR motor assembly are 2 separate parts. Therefore be sure to mount the
CR motor fan with specified adhesive when replacing the CR motor. Make sure that you
leave some portion of 0 to 2 mm on the end of the CR motor shaft, as shown in Figure 3-14.

Base Frame Assembly

CR Motor

CR Motor Pulley

Timing Belt

Belt Tension Spring

Figure 3-13. CR Motor Removal

CR Motor Assembly

Indent side facing outward

CR Motor Fan

Adhesion

Shaft End :0~2 mm

Figure 3-14. Adhering the CR Motor Fan to the CR Motor

Содержание Stylus COLOR 3000





















































































































































































Отзывы:

Нет отзывов