manualshive.com logo in svg

Epson Stylus COLOR 3000, Руководство по обслуживанию, Страница: 31 / 180

Поделиться
Скачать
Epson Stylus COLOR 3000 Скачать руководство пользователя страница 31

Product Descriptions

Rev. A

1-24

Panel Functions (Normal Usage)

Button

Function

Available

Condition

Comment

Operate

Power On/Off

Always

At turning the printer off, the printer executes
capping function before the power down.

Pause

Pause/Non-Pause

Always

Pause
(5 seconds)

Reset

Pause/Standby

The function will be recognized with this
button held down for more than3 seconds.

LF/FF

LF/FF

Pause/Standby

Load/Eject

Load/Eject

Pause/Standby

          

↑

Micro Adjust

Micro adjust
(Forward feed)

Pause/Standby

See Note below.

Micro Adjust
          

↓

Micro adjust
(Reverse feed)

Pause/Standby

See Note below.

Cleaning (Black)
(3 seconds)

Cleaning (Black)

Pause/Standby

The function will be recognized with this
button held down for more than 2 seconds.

Cleaning (Color)
(3 seconds)

Cleaning (Color)

Pause/Standby

The function will be recognized with this
button held down for more than 2 seconds.

Media Type

Selects paper type.

Pause/Standby

Note)  TOF (Top Of Form) adjustment

When ”Micro adjust” is executed for the TOF position, the adjusted TOF position is memorized in
the EEPROM. TOF positions for the ASF, manual insertion and tractor are stored in the
corresponding addresses of EEPROM.
Tear off adjustment
When “Micro adjust” is executed for the tear off position, the adjusted tear off position is
memorized in the EEPROM.

Panel Functions with Power On

Button

Function

Comment

Pause

Enters the printer adjustment mode.

Refer to Section 1.5.3.

LF/FF

Enters LQ self-test print mode.

Refer to Section 1.5.5.

Load/Eject

Enters draft-self test print mode.

Refer to Section 1.5.5.

Media type

Enters the default setting mode.

Refer to Section 1.5.2.

LF/FF

+

Load/Eject

Enters the hex-dump mode.

Refer to Section 1.5.6

Pause

+

LF/FF

+

Micro adjust 

↓

Performs EEPROM and IC reset.

Initializes Timer IC and a part of
the EEPROM.

Note)  ”+” means to press one button while holding down the other button(s).

The power switch is connected to the secondary side of the electrical circuit. Since it has a delay
circuit, voltage is still applied for the specified period of time after the printer power is turned off.

As long as the printer is plugged in, voltage is applied to the primary side of the electrical circuit.
Therefore be sure to unplug the printer before servicing or replacing the interface.

When the EEPROM is reset, the waste ink drain pads need replacing. This must be performed by
a qualified service person only. (See Chapter 3.)

Table 1-28. Panel Functions

Table 1-29. Panel Function with Power On

CAUTION

Содержание Stylus COLOR 3000





















































































































































































Отзывы:

Нет отзывов