Epson Stylus COLOR 3000 Скачать руководство пользователя страница 179

Страница: 179 / 180

EPSON OVERSEAS MARKETING LOCATIONS

EPSON AMERICA, Inc.

20770 Madrona Avenue,
P.O. Box 2842
Torrance, CA 90509-2842
Phone: (800)922-8911
Fax:

(310)782-5220

EPSON DEUTCHLAND GmBH

Zülpicher Straße 6, 4549 Düsseldorf
Germany

Phone: (0211)56030
Telex: 8584786

EPSON UK LTD.

Campus 100, Maylands Avenue,
Hemel Hempstead, Herts, HP2 7TJ
U.K.
Phone: (+44)01442-61144
Fax:

(+44)01442-227227

EPSON FRANCE S.A.

68 bis, rue Marjolin 92300,
Levallois-Perret
France
Phone: (1)4087-3737
Telex: 610657

EPSON IBERICA, S.A.

Avda. de Roma, 18-26
08290 Cerdanyola del Valles
Balcerona, Spain
Phone: 582.15.00
Fax:

582.15.55

EPSON ITALIA S.P.A.

V. le F. lli Casiraghi, 427
20099 Sesto S. Giovanni MI
Italy
Phone: 2-262331
Fax:

2-2440750

EPSON AUSTRALIA PTY. LIMITED

1/70 Gibbes Street,
Chatswood 2067 NSW
Australia
Phone: 2-9903-9000
Fax:

2-9903-9177

EPSON SINGAPORE PTE. LTD.

No.1 Temasek Avenue #36-00
Millenia Tower
Singapore 039192
Phone: (065)3377911
Fax:

(065)3341185

EPSON HONG KONG LTD.

Rooms 4706-10, 47/F
China Resource Bldg.
26 Harbour Road, Wanchai, Hong Kong
Phone: 2585-4300
Fax:

2827-7083

EPSON TAIWAN TECHNOLOGY &
TRADING LTD.

10F, No. 287 Nonking E. Road, Sec. 3,
Taipei, Taiwan, R.O.C.
Phone: (02)717-7360
Fax:

(02)712-9164

EPSON PORTUGAL, S.A.

R. do Progresso, 471, 1° Perafita
4460 Matosinhos, Portugal

Phone: (02)996 14 02
Fax:

(02)996 14 11

SEIKO EPSON CORPORATION
Imaging & Information Products Division

80 Harashinden, Hirooka, Shiojiri-Shi, Nagano-Ken 399-07 JAPAN
Phone: 0263-52-2552
Fax:

0263-54-4007

As of September, 1996

Содержание Stylus COLOR 3000





















































































































































































Результаты поиска

Содержание Stylus COLOR 3000

Отзывы:

Epson Stylus COLOR 3000, Руководство по обслуживанию, Страница: 179 / 180

Результаты поиска

Содержание Stylus COLOR 3000

Отзывы: