manualshive.com logo in svg

Epson Stylus COLOR 3000, Руководство по обслуживанию, Страница: 100 / 180

Поделиться
Скачать
Epson Stylus COLOR 3000 Скачать руководство пользователя страница 100

EPSON Stylus COLOR 3000

Rev. A

3-31

3.2.11.14  CR Unit Removal

1.  Remove the printer mechanism unit. (See Section 3.2.6.)
2.  Disconnect the HP sensor connector cable from the HP sensor.
3.  Remove the belt tension spring to loosen the timing belt.
4.  Disengage the timing belt from the pulley on the CR motor and the sub pulley.
5.  Remove 1 E-ring and 1 plain washer (6X0.7X12) from each end of the CR guide shaft.
6.  If the head cleaner lever* is locking the CR unit, push the lever down manually to unlock the CR unit.

* Head cleaner lever: See Figure 3-20.

7.  Remove 1 screw (CBS, 3X6) and 2 CR mounting shafts securing the black and the color cables with

the head cable guide to the base frame assembly. Then remove the head cable guide and

 

tube

mounting plate

, and remove the ink tubes from the printer mechanism.

8.  Release the coupling screws connecting the ink tubes to

 the ink tube unit

. 

Then remove the tubes.

9.  Turn the parallelism adjust bushings joining the CR guide shaft to the right and left frame assemblies

and release the bushings. Then remove the CR unit along with the CR guide shaft.

10. Remove the CR guide shaft from the CR unit.

Parallelism Adjust Bushing

E-ring

Plain Washer (6X0.7X12)

PG Adjust Lever

HP Sensor Holder

Parallelism Adjust Bushings

E-ring

Plain Washer (6X0.7X12)

CR Guide Shaft

CBS Screw (3X6)

CR Unit

Tube Mounting Plate

Printer Mechanism Unit

Cable Head Guide

CR Mounting Shafts

Figure 3-27. CR Unit Removal

Содержание Stylus COLOR 3000





















































































































































































Отзывы:

Нет отзывов