manualshive.com logo in svg

Epson Stylus COLOR 3000, Руководство по обслуживанию, Страница: 60 / 180

Поделиться
Скачать
Epson Stylus COLOR 3000 Скачать руководство пользователя страница 60

EPSON Stylus COLOR 3000

Rev. A

2-19

ASF_PQ :Output from the PQ (Paper Quantity) sensor.
The paper quantity sensor uses a sliding potentionmeter. (The maximum resistance:10 ohms) The
sensor ,attached to the right edged guide in the hopper assembly, detects the paper quantity between
the maximum of 15 mm and the minimum of 3 mm. The detected quantity is converted into the
corresponding resistance and the information is transferred to the analog port of the 

 

. When the

sensor detects the condition of 3.6 mm which accommodates 25 sheets of 55 kg/m

2

-paper, it outputs

the signal 

.

GAP : Output from the PG (Platen Gap) sensor.
The 

 sensor determines whether the adjust lever is set to the thin paper side or thick paper side.

The signal 

 is 

"

 when the lever is on the thick paper side, and 

 on the thin paper side. This

sensor uses a mechanical switch.

REL : Output from the release sensor.
Release sensor attached to the left and rear side of the printer mechanism determines whether the
release lever is set to friction feed side or tractor side. The signal 

 is 

"

 on the tractor side and is

 on the friction feed side.

CR_PW : Output from the CR PW (Paper Width) sensor.
The

 

 sensor, attached to the left side of the 

 unit, uses a photo interrupt system. While the 

makes 1 return in the paper width seek mode, sensor reads the voltage level of the output signal at
each 

 motor phase change pulse to determine the positions for the both edges of the paper. This

operation prevents printing on the platen. In case no change is detected in paper size from the
previous paper by the 

 

 sensor and ASF PL sensor, the 

 

 sensor is not activated. The

signal output from this sensor is directly sent to the analog port of the 

 

.

Figure 2-21 shows the sensor circuit block diagram.

Data Bus

Address Bus

CPU

H8S/2655

  (IC5)

GA

E05B45

 (IC16)

THS

SWA0

SWA1

SWA2

SWA3

SWC9-11

SWC8

SWC0,2,4

SWC1,3,5

AN0

AN1

AN2

AN3

ASF_PW

ASF_PQ

CR_PW

Thermistor

ASF PW 

Sensor

Paper Quantity

Sensor

CR PW Sensor 

Ink Cartridge Sensor

(B,C,M,Y)

Ink End Sensor

(B,C,M,Y)

Release  Sensor

PL Sensor

HP Sensor

GAP Sensor

Rear PE Sensor

Front PE Sensor

Figure 2-17. Sensor Circuit Block Diagram

Содержание Stylus COLOR 3000





















































































































































































Отзывы:

Нет отзывов