manualshive.com logo in svg

Epson Stylus COLOR 3000, Руководство по обслуживанию, Страница: 139 / 180

Поделиться
Скачать
Epson Stylus COLOR 3000 Скачать руководство пользователя страница 139

EPSON Stylus COLOR 3000

Rev. A

5-11

5.4  Component Repair of the C203 MAIN Board

This section provides information which enables you to repair and replace defective components on the
C203 MAIN board. Table 5-6 and 5-7 lists the causes for each symptom in order of possibility, with which
you are able to find and repair the defective part.

Table 5-6. Component Repair of the C211 MAIN Board

Condition

Cause

Checkpoint

Solution

Symptom : The printer does not operate at all.

Reset circuit is
defective.

Check the following signals for the
waveforms:

IC9:/

        

IC3:

          

+5V

R E S E T

Waveform

 

(6)

Replace the MAIN
board or the reset IC.

CPU doesn’t operate.
(The driver mechanism
doesn’t operate properly
at power on/off.)

Selection of ROM
and sub gate array
is improper.

Check the waveform for one of the
following signals output from the
CPU (IC5) for the change in the
signal High and Low :

/CS0 (Pin 1),    /CS1 (Pin 2),
/CS2 (Pin128), /CS3 (Pin 127)

Waveform (7)

Replace the MAIN
board.

CG-ROM or PROM is defective.

Replace the MAIN
board or PROM.

CPU is defective.

Check the waveform for one of the
following signals output from the
CPU (IC5):

XTAL (Pin 85), EXTAL (Pin 86)

X T A L

Waveform (8)

Replace the MAIN
board or CRU1.

Содержание Stylus COLOR 3000





















































































































































































Отзывы:

Нет отзывов