Epson S1D13706 Скачать руководство пользователя страница 605 | Manualshive

Страница: 605 / 672

Epson S1D13706 Скачать руководство пользователя страница 605

Epson Research and Development

Page 15

Vancouver Design Center

Interfacing to the Motorola RedCap2 DSP With Integrated MCU

S1D13706

Issue Date: 01/02/23

X31B-G-014-02

4.3 S1D13706 Hardware Configuration

The S1D13706 uses CNF7 through CNF0 to allow selection of the bus mode and other
configuration data on the rising edge of RESET#. For details on configuration, refer to the
S1D13706 Hardware Functional Specification, document number X31B-A-001-xx.

The following table shows the configuration required for this implementation of a
S1D13706 to Motorola REDCAP2 microprocessor.

4.4 Register/Memory Mapping

The S1D13706 is a memory mapped device. The S1D13706 uses two 128K byte blocks
which are selected using A17 from the REDCAP2 bus (A17 is connected to the S1D13706
M/R# pin). The internal registers occupy the first 128K byte block and the 80K byte display
buffer occupies the second 128K byte block. In this example, the S1D13706 internal
registers are accessed starting at address 4100 0000h and the display buffer is accessed
starting at address 4102 0000h.

Each Chip Select on the REDCAP2 is allocated a 16M byte block. However, the S1D13706
only needs a 256K byte block of memory to accommodate its register set and 80K byte
display buffer. For this reason, only address bits A[17:0] are used while A[21:18] are
ignored. The S1D13706’s memory and register are aliased every 256K bytes in the 16M
byte CS1 address space.

Note

If aliasing is not desirable, the upper addresses must be fully decoded.

Table 4-2: Summary of Power-On/Reset Options

S1D13706

Pin Name

state of this pin at rising edge of RESET# is used to configure:(1/0)

1

0

CNF[2:0]

101 = REDCAP2 Host Bus Interface

CNF3

GPIO pins as inputs at power-on

GPIO pins as HR-TFT/ D-TFD outputs

CNF4

Big Endian bus interface

Little Endian bus interface

CNF5

WAIT# is active high

WAIT# is active low

CNF[7:6]

CLKI to BCLK divide select:

CNF7 CNF6 CLKI to BCLK Divide Ratio

0 0 1 : 1

0 1 2 : 1

1 0 3 : 1

1 1 4 : 1

= configuration for REDCAP2 microprocessor

«
...
603
604
605
606
607
...
»

Содержание S1D13706

































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов