Epson LQ-1150 II Скачать руководство пользователя страница 126

Страница: 126 / 129

IN-2

Manual feed wait time, 2-9
Micro adjust, 2-22 to 2-24, 2 -25 to 2-26
Multipart forms

printing, 2-30

Options

Cut-sheet feeder, 2-33 to 2-37
Pull tractor unit, 2-37 to 2 -38
Roll paper holder, 2-39 to 2 -40

Packet mode, 2-8
Page length for tractor, 2-5
Panel.

See

Control panel

Paper alignment, A-15
Paper specifications, A-8 to A-10
Paper-thickness lever, 2-28 to 2-29
Parallel I/F (interface) bidirectional

mode, 2-7

Parity, 2-7
Printable area, A-11 to A-13
Print direction, 2-5 to 2 -6
Printer driver

accessing

from Windows 2000 or NT 4.0,

3-5 to 3 -9

from Windows Me, 98 or 95,

3-2 to 3 -4

installing

for DOS, 1-22
for Windows Me, 98, 95, 2000 or

NT 4.0, 1-21 to 1-22

settings, 3-11 to 3-12

Printer software

installing, 1-20 to 1 -22

Print Head Caution Symbol, 3

Removing

printed document from

push tractor, 2-15 to 2-16

Ribbon cartridge, 1-8 to 1 -12
Roll paper

default setting, 2-9
printing, 2-39 to 2-40

Roll paper holder, 2-39 to 2-40

Safety instructions, 2 to ??
Self test, 1-13 to 1-15
Single sheets

printing, 2-27

Skip over perforation, 2-5
Software

default setting, 2-6

See

Printer software

Specifications

built-in font, A-6
character tables, A-7
command lists

ESC/P 2, A-16 to A-17
IBM PPDS emulation,

A-17 to A -18

electrical, A-7
environmental, A-8
international character sets, A-7
mechanical, A-4 to A -5
paper, A-8 to A-10
paper alignment, A-15
printable area, A-11 to A -13

Status Monitor 3 utility.

See

EPSON

Status Monitor 3 utility

Tear-off, 2-24 to 2-26

adjusting, 2-25 to 2 -26
automatically, 2-25

Technical support, A-18
Transporting the printer, A-3

Содержание LQ-1150 II


































































































































Результаты поиска

Содержание LQ-1150 II

Отзывы:

Epson LQ-1150 II, Руководство пользователя, Страница: 126 / 129

Результаты поиска

Содержание LQ-1150 II

Отзывы: