Epson LQ-1150 II Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 129

background image

1-22

Setting Up the Printer

3. Double-click

Install Printer Driver/Utility

to start the printer

software installation, then follow the instructions on the
screen.

When you install the printer driver on Windows Me, 98, 95, 2000
or NT 4.0, the EPSON Status Monitor 3 utility will also be
installed.

For information on launching and using the software, see Chapter
3, “Using the Printer Software.”

For DOS programs

To control the printer from DOS application programs, you need
to select the printer you are using or another available printer
from the printer list of your application.

Choose the EPSON LQ-1150 printer at the appropriate step in the
setup or installation procedure of your DOS application program.
If the list in your application does not include the LQ-1150 printer,
choose the first available printer from this list:

Note:

If your application does not list a suitable alternative, contact the
software manufacturer to see if an update is available.

LQ-2180/LQ-2080

LQ-200

LQ-2170/LQ-2070

LQ-500

LQ-1070/1070 +

LQ-860 +/1060 +

LQ-870/1170

LQ-2550

LQ-850 +/1050 +

LQ-2500

LQ-850/1050

LQ-800/1000

LQ-510/550/1010

LQ-1500

«
...
32
33
34
35
36
...
»

Содержание LQ-1150 II


































































































































Отзывы:

Нет отзывов

Похожие инструкции для LQ-1150 II

imagePROGRAF iPF760

Бренд: Canon Страницы: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Бренд: Canon Страницы: 16

imagePRESS C850

Бренд: Canon Страницы: 146

imagePRESS C850

Бренд: Canon Страницы: 63

imagePROGRAF iPF760

Бренд: Canon Страницы: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Бренд: Canon Страницы: 8

imagePROGRAF TX-2000

Бренд: Canon Страницы: 14

i-SENSYS MF6180dw

Бренд: Canon Страницы: 1040

imagePROGRAF iPF815

Бренд: Canon Страницы: 48

imageRUNNER 1025

Бренд: Canon Страницы: 6

imageRUNNER 2230

Бренд: Canon Страницы: 6

IMAGEPRESS C7010VPS

Бренд: Canon Страницы: 388

Бренд: Canon Страницы: 56

imagePROGRAF iPF8300

Бренд: Canon Страницы: 24

imagePROGRAF iPF8300

Бренд: Canon Страницы: 4

imagePROGRAF iPF6350

Бренд: Canon Страницы: 12

imagePROGRAF iPF6350

Бренд: Canon Страницы: 2

imageCLASS MF8380Cdw

Бренд: Canon Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды