Epson LQ-1150 II Скачать руководство пользователя страница 20

Страница: 20 / 129

1-8

Setting Up the Printer

1. Make sure the power switch on the printer is turned off. It is

off when the

side of the switch is pressed down.

2. Check the label on the back of the printer to make sure the

voltage required by the printer matches that of your electrical
outlet.

Caution:

If the rated voltage on the printer and your outlet voltage do
not match, contact your dealer for assistance. Do not plug in
the power cord.

3. If the power cord is not attached to the printer, connect it to

the AC inlet on the printer.

4. Plug the power cord into a properly grounded electrical

outlet.

Installing or replacing the ribbon cartridge

Before installing the ribbon cartridge, make sure that the printer
is not plugged into an electrical outlet.

Follow these steps to install or replace the ribbon cartridge:

1. make sure the printer is turned off.

Содержание LQ-1150 II


































































































































Результаты поиска

Содержание LQ-1150 II

Отзывы:

Epson LQ-1150 II, Руководство пользователя, Страница: 20 / 129

Результаты поиска

Содержание LQ-1150 II

Отзывы: