Enviro E20 Скачать руководство пользователя

Страница: 12 / 40

Maintenance And Service

emoVing

aLVe

oVeR

The valve cover can be removed to access the gas valve, the fan, wiring harness, or other components.

1. Remove the glass door as shown in the

aIntenance

anD

erVIce

- g

lass

oor

emoVal

2. Carefully remove the log set, ember

material, and brick panels, refer to

econDary

nstallatIon

- b

rIck

anel

nstallatIon

and

econDary

nstallatIon

- l

anD

mber

nstallatIon

3. Using a T-20 screwdriver remove the two

(2) screws that hold the burner tray in

place (pointed out in Figure 10). Pick up

the burner tray at the front (see Figure 11)

then pull it out of the firebox.

4. Using a T-20 screwdriver remove the six

(6) screws that hold the valve cover in

place (pointed out in Figure 12). Pick the

valve cover up then out of the firebox (see

Figure 13).

Figure 10: Screws Holding Burner Tray in Place.

Figure 12: Screws Holding Valve Cover in Place.

Figure 11: Removing Burner Tray.

Figure 13: Removing Valve Cover.

ueL

onVeRsion

TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY

Please read and understand these instructions before installing.

Warning: This conversion kit shall be installed by a qualified service agency in accordance

with the manufacturer’s instructions and all applicable codes and requirements of the

authority having jurisdiction. If the information in these instructions is not followed

exactly, a fire, explosion or production of carbon monoxide may result causing property

damage, personal injury or loss of life. The qualified service agency is responsible for

the proper installation of this kit. The installation is not proper or complete until the

operation of the converted appliance is checked as specified in the manufacturer’s

instructions supplied with the kit.

Содержание E20









































Результаты поиска

Содержание E20

Отзывы:

Похожие инструкции для E20

Бренды по названию

Популярные бренды

Enviro E20, Руководство пользователя

Результаты поиска

Содержание E20

Отзывы:

Похожие инструкции для E20

Бренды по названию

Популярные бренды