Enviro E20 Скачать руководство пользователя

Страница: 3 / 40

Table of Contents

Safety Precautions...........................................................................................................2

Table of Contents.............................................................................................................3

Codes And Approvals.......................................................................................................4

Specifications..................................................................................................................5

Rating Label Location...........................................................................................5

Dimensions..........................................................................................................5

E20 Options Dimensions.........................................................................................6

Operating Instructions....................................................................................................7

Lighting and Turning Off Instructions.....................................................................7

Pilot Light.............................................................................................................8

Venturi Adjustment...............................................................................................8

Normal Sounds During Operation.........................................................................8

Burner Lighting.....................................................................................................9

Blower Speed.......................................................................................................9

Maintenance And Service................................................................................................10

Cleaning The Glass.............................................................................................10

Cleaning The Firebox..........................................................................................10

Replacing The Glass............................................................................................10

Check Pilot and Burner Flames............................................................................10

Glass Door Removal...........................................................................................11

Cleaning The Painted Surfaces............................................................................11

Removing Valve Cover.........................................................................................12

Fuel Conversion..................................................................................................12

Initial Installation...........................................................................................................15

Clearances to Combustibles.................................................................................15

Minimum Fireplace Size.......................................................................................15

Direct Vent Model...............................................................................................15

Preparing Your E20 For Installation........................................................................16

Venting Fireplace Inserts.....................................................................................17

Direct Vent Vertical Vent Termination...................................................................19

Electrical Requirements.......................................................................................21

Gas Line Connection...........................................................................................22

Adjusting The Pilot Flame....................................................................................24

Secondary Installation....................................................................................................25

Optional Base Shelf & Riser.................................................................................25

Optional 3 and 4 sided Trim-able Panels...............................................................26

Surround Panel Installation..................................................................................27

Log and Glass Burner Options................................................................................28

Optional Rocks for Glass Burner............................................................................29

Firebox Liner Installation.....................................................................................30

Log Set and Ember Installation............................................................................31

Trouble Shooting............................................................................................................34

Parts List.......................................................................................................................35

Parts Diagram - Components..........................................................................................37

Parts Diagram - Options.................................................................................................38

Warranty.......................................................................................................................39

Installation Data Sheet...................................................................................................40

Содержание E20









































Результаты поиска

Содержание E20

Отзывы:

Похожие инструкции для E20

Бренды по названию

Популярные бренды

Enviro E20, Руководство пользователя

Результаты поиска

Содержание E20

Отзывы:

Похожие инструкции для E20

Бренды по названию

Популярные бренды