background image

30

IP2085EN - 2014-09-01

These precautions are an integral and essential part of the product 

and must be supplied to the user.

Read them carefully since they contain important information on safe 

installation, use and maintenance.

These instructions must be kept and forwarded to all possible future 

users of the system. 

This product must only be used for the specific purpose for which it 

was designed.

Any other use is to be considered improper and therefore dangerous. 

The manufacturer cannot be held responsible for any damage caused 

by improper, incorrect or unreasonable use.

Avoid operating in the proximity of the hinges or moving mechanical 

parts. Do not enter within the operating range of the motorised door 

or gate while it is moving.

Do not obstruct the motion of the motorised door or gate, as this may 

cause a dangerous situation.

The motorised door or gate may be used by children over the age of 8 

and by people with reduced physical, sensorial or mental abilities, or 

lack of experience or knowledge, as long as they are properly supervised 

or have been instructed in the safe use of the device and the relative 

hazards.

Children must be supervised to make sure they do not play with the 

device, nor play/remain in the sphere of action of the motorised door 

or gate.

Keep remote controls and/or any other command devices out of the 

reach of children, to avoid any accidental activation of the motorised 

door or gate.

In the event of a product fault or malfunction, turn off the power supply 

switch. Do not attempt to repair or intervene directly, and contact only 

qualified personnel.

Failure to comply with the above may cause a dangerous situation.

Any repair or technical intervention must be carried out by qualified 

personnel.

Cleaning and maintenance work must not be carried out by children 

unless they are supervised. 

To ensure that the system works efficiently and correctly, the manufac-

turer’s indications must be complied with and only qualified personnel 

must perform routine maintenance on the motorised door or gate. In 

particular, regular checks are recommended in order to verify that the 

safety devices are operating correctly.

All installation, maintenance and repair work must be documented and 

General safety precautions for the user

Содержание Ditec QIK80EH

























Отзывы: