background image

43

IP2085EN - 2014-09-01

Operating instructions

General safety precautions 

for the user

DET

ACH AND DELIVER T

O THE CUST

OMER

These precautions are an 

integral and essential part of 

the product and must be supplied 

to the user.

Read them carefully since they 

contain important information on 

safe installation, use and main-

tenance.

These instructions must be kept 

and forwarded to all possible future users of the system. 

This product must only be used for the specific purpose for which it was 

designed. Any other use is to be considered improper and therefore 

dangerous. 

The manufacturer cannot be held responsible for any damage caused 

by improper, incorrect or unreasonable use.

Avoid operating in the proximity of the hinges or moving mechanical 

parts.  Do not enter within the operating range of the motorised door 

or gate while it is moving.

Do not obstruct the motion of the motorised door or gate, as this may 

cause a dangerous situation. 

The motorised door or gate may be used by children over the age of 8 

and by people with reduced physical, sensorial or mental abilities, or 

lack of experience or knowledge, as long as they are properly supervised 

or have been instructed in the safe use of the device and the relative 

hazards.

Do not allow children to play or stay within the operating range of the 

motorised door or gate.

Keep remote controls and/or any other command devices out of the 

reach of children, to avoid any accidental activation of the motorised 

door or gate.

In the event of a product fault or mal-

function, turn off the power supply 

switch. Do not attempt to repair or 

intervene directly, and contact only 

qualified personnel.

Failure to comply with the above may 

cause a dangerous situation.

Содержание Ditec QIK80EH

























Отзывы: