background image

POWER FACTOR CONTROLLER

RG3-15C/CS/CL/CLS

SUMMARY

Precautions for Safe Use and Installation

.......................................................................................................

1

Important Note for System Connection 

.............................................................................................................

1

1. INTRODUCTION 

..........................................................................................................................................................................

2

1.1

General Information ............................................................................................................................................

2

1.2

Front Panel .................................................................................................................................................................

2

1.3

Rear Panel ..............................................................................................................................................................

4

2. INSTALLATION OF RG3-15C/CS/CL/CLS

.....................................................................................................................

5

2.1

Commissioning of RG3-15C/CS/CL/CLS ..........................................................................................................................

5

2.2 

Step Sequence Process ...........................................................................................................................................

5

3. SETTINGS 

.................................................................................................................................................................

5

3.1 

Manual Operation, Automatic Capacitor Recognition Mode and Automatic Connection Recognition Mode...........

6

3.2 

Target Cos

j

 and Cos

j

2

Value Setting ....................................................................................................................

7

3.3 

Selection of Proper Switching Sequence.........................................................................................................................

8

3.4 

Switching on&off Time for Capacitor Steps and Discharge Time Settings.................................................................

8

3.5 

Power Value and Connection Type Settings for Capacitors ........................................................................................

10

3.6 

Current and Voltage Transformer Ratio Settings .......................................................................................................

12

3.7 

Reset Settings .....................................................................................................................................................

14

3.8 

Alarm Settings .....................................................................................................................................................

15

3.9

Resetting the Energy Counters and Entering the Energy Values..................................................................................

20

3.10  Computer Communication Settings .................................................................................................................................

21

3.11  Password Activation and Change Settings .............................................................................................................

23

4. DISPLAYING OF INSTANTANEOUS VALUES 

......................................................................................................

25

Cos

j, 

Total Cos

j

, Voltages ................................................................................................................................

25

Currents, Active Powers, Total Active Powers ...........................................................................................................

26

Reactive Powers, Total Reactive Powers, Apparent Powers, Total Apparent Powers......................................

27

Active Import Energy, Active Export Energy, Inductive Reactive Energy, Capacitive Reactive Energy,

                Error Codes ......................................................................................................................................................

28

5. APPENDIX 

.......................................................................................................................................................................

29

 

Error Messages ................................................................................................................................................

29

 

Register Table 

..................................................................................................................................................

30

Capacitor Calculation Table ............................................................................................................................................

35

 

Technical Features ..............................................................................................................................................

36

 

Menu Map .............................................................................................................................................................

A5372b/Rev.3

Содержание RG3-15C






































Отзывы: