Enovation Controls Murphy EMS PRO LITE Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 63

background image

Section 40

00-02-0787

2015-03-23

~ 28 ~

S-#

Description

S41

SENDER TYPES: (S41 is only visible if S38=Mechanical.)
This set point allows you to select between Murphy-resistive sending
units or VDO-resistive sending units for Pressure and Temperature
senders.

Factory set to MURPHY

.

S42

START DLY: Set this delay on engine start to the number of seconds
that the start signal must be present before the controller accepts it
and initiates an auto start sequence (adjustable from 1 to 9,999
seconds).

Factory set to 1.

S43

PRESTART DLY: The time the prestart output is turned ON prior to
cranking the engine (adjustable from 1 to 9,999 seconds).

Factory

set to 1.

S44

STOP DLY: Set this delay on engine stop to the number of seconds
that the stop signal must be present before the controller accepts it
and initiates a stop sequence (adjustable from 1 to 9,999 seconds).

Factory set to 1.

S45

START PSI: (S45 is only visible if S35 = Transducer & S37 =
Pressure.) When “pressure” is selected in the start / stop type, an auto
start will occur when the discharge pressure drops to this set point.
(adjustable from 0 to 1000 PSI)

Factory set to 40.

S46

STOP PSI: (S46 is only visible if S35 = Transducer & S37 =
Pressure.) When “pressure” is selected in the start / stop type, an auto
stop will occur when the discharge pressure rises to this set point.
(adjustable from 0 to 1000 PSI)

Factory set to 60.

S47

MAINTAIN PSI: (S47 is only visible if S35 = Transducer & S37 =
Pressure.) When “pressure” is selected in the throttle type, the engine
will be throttled between the “minimum” and “maximum” rpm set
points to maintain this pressure. (adjustable from 0 to 1000 PSI)

Factory set to 50.

S48

DEADBAND PSI: (S45 is only visible if S35 = Transducer & S37 =
Pressure.) When

PRESSURE

is selected in the throttle type, no

throttling will occur while the pressure is in the deadband. This set
point extends above and below the maintain set point (adjustable from
0 to 50 PSI).

Factory set to 2.

«
...
34
35
36
37
38
...
»

Содержание Murphy EMS PRO LITE
































































Отзывы:

Нет отзывов

Похожие инструкции для Murphy EMS PRO LITE

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: Ebyte Страницы: 34

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: Quickmill Страницы: 3

Бренд: Dantherm Страницы: 96

Бренд: JANE Страницы: 144

SHERPA MONOBLOC B0812

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 16

Бренд: Paradox Страницы: 32

Бренд: Valcom Страницы: 6

Бренд: Water Specialist Страницы: 60

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды