Enovation Controls Murphy EMS PRO LITE Скачать руководство пользователя страница 54

Страница: 54 / 63

Section 40

00-02-0787

2015-03-23

~ 46 ~

REGISTER

TYPE

DESCRIPTION

40008

Read Only

Shutdown Status: Bits description follows:

Bit 0

(LSB) Low Oil Pressure: (1) yes, (0) no.

Bit 1

High Engine Temperature: (1) yes, (0)
no.

Bit 2

Spare

Bit 3

Spare

Bit 4

Loss of Speed: (1) yes, (0) no.

Bit 5

No Speed Signal: (1) yes, (0) no.

Bit 6

Overspeed: (1) yes, (0) no.

Bit 7

Overcrank: (1) yes, (0) no.

Bit 8

High Discharge Pressure: (1) yes, (0)
no.

Bit 9

Low Discharge Pressure: (1) yes, (0)
no.

Bit 10 High System Level: (1) yes, (0) no.

Bit 11 Low System Level: (1) yes, (0) no.

Bit 12

Loss of Pressure Sender: (1) yes, (0)
no.

Bit 13 Spare

Bit 14 Spare

Bit 15 Spare

40009

Read Only

Shutdown Status: Bits description follows:

Bit 0

Reserved

Bit 1

Low Fuel Level Alarm: (1) yes, (0) no.

Bit 2

Low Fuel Level Shutdown: (1) yes, (0)
no.

Bit 3

Spare.

Bit 4

Spare.

Bit 5

Spare.

Содержание Murphy EMS PRO LITE
































































Результаты поиска

Содержание Murphy EMS PRO LITE

Отзывы:

Похожие инструкции для Murphy EMS PRO LITE

Бренды по названию

Популярные бренды

Enovation Controls Murphy EMS PRO LITE, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Murphy EMS PRO LITE

Отзывы:

Похожие инструкции для Murphy EMS PRO LITE

Бренды по названию

Популярные бренды