manualshive.com logo in svg

Enovation Controls Murphy EMS PRO LITE, Инструкция по установке и эксплуатации

Поделиться
Скачать
Enovation Controls Murphy EMS PRO LITE Скачать руководство пользователя страница 33

 

Section 40 

00-02-0787 

2015-03-23

 

~ 25 ~

 

S-# 

Description 

S19 

COOLDOWN DLY: You can adjust this variable to the number of 
seconds you wish to cool down your engine before it shuts OFF after 
a stop signal is received (adjustable from 1 to 9,999 seconds). 

Factory set to 180.

 

S20 

CRANK TIME: Set this delay to the desired amount of time you want 
each engine-cranking attempt to last. Consult your engine manual for 
recommended cranking and resting times (adjustable from 1 to 30 
seconds). 

Factory set to 10.

 

S21 

REST TIME: Set this delay to the desired amount of time you want 
each rest period between cranking attempts to last. Consult your 
engine manual for recommended resting and cranking times 
(adjustable from 1 to 30 seconds). 

Factory set to 10.

 

S22 

RECRANK DELAY: This delay is used to adjust the amount of time 
the controller will wait for the engine to stop moving before attempting 
another crank if a false start occurs. During a false start, the engine 
starts but then dies before the LOCKOUT DELAY (S9) has expired 
(adjustable from 1 to 30 seconds). 

Factory set to 10.

 

S23 

CRANK STOP RPM:  This RPM set point is used to adjust where the 
controller releases the starter during cranking. Set this to the RPM the 
engine attains just as it starts. Set this way, the starter is not 
unnecessarily engaged after the engine starts. This is how the 
controller senses whether the engine is running or not. 

Factory set to 

300.

 

S24 

CRANK ATTEMPTS: Set the number of attempts you would like the 
controller to try an engine start. If the engine fails to start after the 
number of attempts you have selected, it will fail and display 
OVERCRANK on the front display. This shutdown requires a manual 
reset. 

Factory set to 6.

 

S25 

WARMUP RPM: This is the engine RPM the controller will throttle the 
engine to during warm-up in auto mode. Consult the engine manual 
for the optimum warm-up speed. (adjustable from 1 to 9,999 seconds) 

Factory set to 600.

 

S26 

COOLDOWN RPM: This is the engine RPM the controller will throttle 
the engine to during cooldown. Consult the engine manual for the 
optimum cooldown speed. 

Factory set to 600.

 

S27 

MIN ENG RPM:  When throttling in the AT LOAD state, the engine will 
not throttle below this set point. 

Factory set to 750.

 

Содержание Murphy EMS PRO LITE
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды