Enovation Controls Murphy EMS PRO LITE Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 63

background image

Section 40

00-02-0787

2015-03-23

~ 12 ~

If you are using the

EMS PRO LITE

on an Interim Tier 4 engine, please

read and understand the information for the following S-numbers: S73,
S74, and S75 in the S-number table, page 22. Also, read and understand
the following information and steps to set up Tier 4 Emission options.
The controller displays the SOOT level on the display when the engine
has been de-rated and/or when regeneration (regen) is required to return
to normal service. You must set S73 (Tier Rating) to

Tier 4

for these

options to be available.

•

If S74 (Tier State) is set to Auto DPF Regen, the ECU
performs a regen automatically. This only occurs if the
ECU conditions allow.

•

If S75 (Request DPF Regen) is set to YES, the controller
commands the ECU to perform a regen. This only occurs
if ECU conditions allow.

•

If S75 (Request DPF Regen) is set to NO, Inhibit Regen is
active and no regen occurs.

To use the controller on a Tier 4 engine, follow the steps below:

1.

Access the S Menu by pressing

[Menu]

.

2.

Press the

[Up or Down Arrow]

to scroll to the correct

Entry Code (See Entry Code Supplement for Entry
Codes).

3.

Press the

[Up or Down Arrow]

until S73 (Tier Rating)

is displayed in the menu and press

[Enter]

.

4.

Press the

[Up or Down Arrow]

until TIER 4 is

highlighted and press

[Enter]

.

5.

Press the

[Up or Down Arrow]

until S74 (Tier State)

is highlighted and press

[Enter]

. The default value is

set to INHIBIT. To select

Auto DPF Regen

use the

[Up or Down Arrow]

to highlight the text and press

[Enter]

.

To use the Request DPF Regen feature, follow these steps (If all the
conditions for a regen to occur are not met, this request could be ignored
by the ECU):

1.

Access the S Menu by pressing

[Menu]

2.

Press the

[Up or Down Arrow]

and scroll to the

correct Entry Code (See Entry Code Supplement for
Entry Codes).

3.

Press the

[Up or Down Arrow]

until S75 (Request

DPF Regen) is displayed in the menu and press

[Enter]

.

4.

Press the

[Up Arrow]

until YES is highlighted and

press

[Enter]

.

«
...
18
19
20
21
22
...
»

Содержание Murphy EMS PRO LITE
































































Отзывы:

Нет отзывов

Похожие инструкции для Murphy EMS PRO LITE

Бренд: Hanna Instruments Страницы: 88

Black Force Wireless

Бренд: Hama Страницы: 10

Бренд: olympia electronics Страницы: 10

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренд: Delabie Страницы: 20

Бренд: Linear Technology Страницы: 32

Бренд: nurse Страницы: 24

Бренд: Westfalia Страницы: 18

Controller CR100

Бренд: Sonos Страницы: 2

Бренд: M-system Страницы: 5

Бренд: Satel Страницы: 7

Бренд: VAT Страницы: 12

Бренд: Ebyte Страницы: 25

Бренд: Bard Страницы: 102

Бренд: Vestil Страницы: 6

Бренд: Hach Страницы: 48

Бренд: Nacon Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды