ENFORCER Outdoor Stand-Alone/Wiegand Keypad with Proximity Reader
20
SECO-LARM U.S.A., Inc.
The keypad must be connected to a Request-to-Exit (RTE) button to be reset to factory default settings.
When resetting to factory default, user information is retained. You may also program new Master Add
and Master Delete Card if they are lost. To reset the keypad to factory default settings, follow steps 1~4
below. To also program new Master Add and Master Delete cards, follow steps 1~3 and 5 below.
NOTE:
Programming new Master Add and Master Delete cards will delete the previous Master Add and
Master Delete cards.
1.
Power off the keypad
2.
Hold down the egress button and power the keypad on, continuing to hold down the egress button
for approximately 10 seconds until you hear 2 beeps and the LED turns orange.
3.
Release the egress button.
4.
If you only need to reset the keypad to factory default, wait until the LED changes to red (about 30
seconds) indicating that the reset has completed successfully.
5.
If you need to program new Master Add and Master Delete Cards, within 30 seconds, read two
cards. The first will become the Master Add Card, and the second the Master Delete Card. The LED
will change to red indicating that the reset has completed successfully.
Resetting to Factory Default and Programming Add/Delete Cards:
Additional Accessories Available from
SECO-LARM
®
:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
®
PICSN8
MI_SK-2612-SPQ_191030.docx
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM
U.S.A., Inc. or their respective owners. Copyright © 2019 SECO-LARM U.S.A., Inc. All rights reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1)
year from the date of sale to the original customer. SECO LARM’s obligation is limited to the repair or replacement of any defective part if the
unit is returned, transportation prepaid, to SECO LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or
electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO
LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The
sole obligation of SECO LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO LARM’s
option. In no event shall SECO LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any
kind to the purchaser or anyone else.
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies
with all national, state, and local laws and codes related to locking and egress devices. SECO-LARM will not be held responsible for the use
of this product in violation of any current laws or codes.
FCC COMPLIANCE STATEMENT
FCC ID: K4E2612SPQ
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.
Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to
operate the device.
IMPORTANT WARNING:
For a weather-resistant installation, ensure that the unit is properly sealed where the housing base meets the wall.
Incorrect mounting may lead to exposure to rain or moisture in the enclosure which could cause a dangerous electric shock, damage the
device, and void the warranty. Users and installers are responsible for ensuring that this product is properly installed and sealed.
PR-K1K1-AQ
Proximity key fobs
(sold in packs of 10)
PR-K1S1-A
Proximity cards
(sold in packs of 10)
