Enerzone EUROSTAR Скачать руководство пользователя

Страница: 52 / 72

Eurostar Installation and Operation Manual



The flue is not properly installed.

Make sure the venting system meets the criteria in the

installation section of this manual as well as the venting system manufacturer’s instructions.



The flue is blocked or needs cleaning.

One of the following components is obstructed or

blocked; air intake shutter, combustion blower, burn pot, heat exchangers and channels,

exhaust blower and or venting system. Refer to the maintenance section.



The stove needs maintenance.

Refer to maintenance section.



The burn pot is not installed properly.

Make sure the burn pot is well installed and locked in

place.



The baffle is not installed properly

. Make sure all three panels are well installed.



The convection blower is defective.

Go to the troubleshooting page (see

Section 9.2

Testing Components

) on the LCD screen and test the convection blower.



The convection blower needs maintenance.

Carefully clean blower housing and make sure

blower louvers are not blocked.

NOTE: IF THE CODE APPEARS MORE THAN THREE TIMES, THE LCD SCREEN WILL LOCK

ITSELF UP AND YOU WILL NEED TO CALL A SERVICE TECHNICIAN TO UNLOCK IT.



The hopper lid remained open for more than 3 minutes.

As a security measure, the auger

stops turning and feeding pellets as soon as the hopper lid opens. It will resume normal

operation as soon as the hopper lid is closed. If the hopper lid stays open for more than 3

minutes, the stove will stop.



The hopper lid switch is defective or misconnected.

Make sure the switch is properly

connected. If it is, the hopper switch may be defective. Go to the troubleshooting page (see

Section 9.2

Testing Components

) and check the functionality of the switch. Replace if

necessary.

THE FOLLOWING MAY HAVE CAUSED YOUR

PROBLEM (HOPPER LID):

•

THE HOPPER LID REMAINED OPEN FOR
MORE THAN 3 MINUTES

•

THE HOPPER LID SWITCH IS DEFECTIVE
OR MISCONNECTED

BACK

THE HOPPER LID HAS

REMAINED OPEN FOR MORE

THAN 3 MINUTES

RESET

HOPPER LID OPEN

DETAILS

CONSULT OWNER’S MANUAL FOR

MORE DETAILS

POWER WAS INTERRUPTED

WHILE BURNING

RESET

POWER LOSS

Содержание EUROSTAR









































































Результаты поиска

Содержание EUROSTAR

Отзывы:

Похожие инструкции для EUROSTAR

Бренды по названию

Популярные бренды

Enerzone EUROSTAR, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EUROSTAR

Отзывы:

Похожие инструкции для EUROSTAR

Бренды по названию

Популярные бренды