Enerpac NC-1924, Инструкция

Страница: 2 / 52

2
hose materials and packings. For optimum performance do not
expose equipment to temperatures of 65°C [150°F] or higher.
Protect hoses and cylinders from weld spatter.
DANGER: Do not handle pressurized hoses. Escaping
oil under pressure can penetrate the skin, causing serious
injury. If oil is injected under the skin, see a doctor
immediately.
WARNING: Only use hydraulic cylinders in a coupled
system. Never use a cylinder with unconnected couplers. If
the cylinder becomes extremely overloaded, components
can fail catastrophically causing severe personal injury.
WARNING: BE SURE SETUP IS STABLE BEFORE
LIFTING LOAD. Cylinders should be placed on a flat
surface that can support the load. Where applicable, use a
cylinder base for added stability. Do not weld or otherwise
modify the cylinder to attach a base or other support.
Avoid situations where loads are not directly centered
on the cylinder plunger. Off-center loads produce
considerable strain on cylinders and plungers. In addition,
the load may slip or fall, causing potentially dangerous results.
Distribute the load evenly across the entire saddle
surface. Always use a saddle to protect the plunger.
IMPORTANT: Hydraulic equipment must only be serviced
by a qualified hydraulic technician. For repair service,
contact the Authorized ENERPAC Service Center in your
area. To protect your warranty, use only ENERPAC oil.
WARNING: Immediately replace worn or damaged parts
by genuine ENERPAC parts. Standard grade parts will
break causing personal injury and property damage.
ENERPAC parts are designed to fit properly and withstand high
loads.
WARNING: To prevent injury, do not place fingers on or
near the cutting blade while the nut splitter is operating.
WARNING: To prevent injuries and avoid damage to
the cutters, do not use the nut splitter on glass, plastic,
wood, or any other material which could shatter.
CAUTION: To avoid damage to the nut splitter blade,
housing, plunger and seals:
* Do not cut chains or bolts.
* Do not use the nut splitter to rotate nuts.
* Do not move the nut splitter during the cutting operation.
* Do not heat up nuts while the nut splitter is in position.
CAUTION: Enerpac nut splitters are designed specifically
for metal nuts which match sizes shown in the
specifications chart. (Maximum allowable hardness of
nuts to be split is HRc-44.) For materials and sizes not specified,
contact Enerpac Technical Services.
danger.eps
danger.eps
danger.eps
danger.eps
inject.eps
sman.eps
danger.eps
®
stblty.eps
bdyhit.eps
C
A
D
F
B
H
J
C
A
D
F
B
H
J
Single (NC)
Double (NC-D)
Specifications - Dimensions in Inches (mm)
Model Bolt Range Nut Range Capacity Weight A B C D F H J
No. in (mm) in (mm) (tons) lb (kg)
NC-1019
5/16 - 1/2 3/8 - 3/4
5 1.8 1.57 6.69 .27 .75 1.10 1.89 .83
(M6-M12) (10-19) (0.8) (40) (170) (7) (19) (28) (48) (21)
NC-1924
1/2 - 5/8 3/4 - 15/16
10 4.4 2.17 7.52 .32 1.02 1.57 2.44 .98
(M12-M16) (19-24) (2.0) (55) (191) (8) (26) (40) (62) (25)
NC-2432
5/8 - 7/8 15/16 -
1
1/8
15 6.6 2.52 8.74 .39 1.14 2.01 2.83 1.30
(M16-M22) (24-32) (3.0) (64) (222) (10) (29) (51) (72) (33)
NC-3241
7/8 -
1
1/8
1
1/8 -
1
9/16
20 9.7 2.95 9.61 .67 1.42 2.60 3.46 1.69
(M22-M27) (32-41) (4.4) (75) (244) (17) (36) (66) (88) (43)
NC-4150
1
1/8 -
1
3/8
1
9/16
-
2
35 18.0 3.70 11.34 0.83 1.77 2.91 4.13 2.13
(M27-M33) (41-50) (8.2) (94) (288) (21) (45) (74) (105) (54)
NC-5060
1
3/8 -
1
1/2
2
-
2
1/4
50 26.0 4.17 12.52 .91 2.13 3.54 5.04 2.36
(M22-M27) (32-41) (11.8) (106) (318) (23) (54) (90) (128) (60)
NC-6075
1
1/2
-
1
7/8
2
3/8 -
2
7/8
56 75.1 6.14 15.47 1.02 2.83 4.33 7.13 3.15
(M39-M43) (60-75) (34.1) (156) (393) (26) (72) (110) (181) (80)
* Previously known as NC-1319