Endace DAG 5.2X Скачать руководство пользователя

Страница: 27 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

eql/noeql

Sets or unsets equipment loopback. For testing set to

eql

mode and normal operation set to

noeql

mode.

Note:

eql

mode loops transmit data from the host back to the PCIe bus.

Example

dagconfig eql
dagconfig noeql

fcl/nofcl

Note:

Sets or unsets Facility loop back. For testing set to

fcl

mode and normal operation

set to

nofcl

mode.

FCL retransmits the data received and also send it to the host.

Example

dagconfig fcl
dagconfig nofcl

laser/nolaser

Enables/disables the transmit laser on for the optical transceivers.

Example

dagconfig laser
dagconfig nolaser

mem

You can split the DAG card's allocated memory between the receive and transmit stream

buffers to suit your own requirements. The split is displayed as a ratio as shown below:

mem=X:Y

where:

is the memory allocated in MB to the

stream

is the memory allocated in MB to the

stream.

If there are multiple

streams memory can be allocated to each stream:

mem=X:Y:X:Y:X:Y

Buffer_size

(page ) and

rx and tx Streams

(page ) are related to

mem

Example

You can split 128MB of memory evenly between the

and

streams using:

dagconfig –d0 mem=64:64

Note:

You can not change the stream memory allocations while packet capture or

transmission is in progress.

nic / nonic

Note:

From DAG software 3.1.0 onwards

nic/nonic

is replaced by

auto_neg/noauto_neg

Both options are valid and still can be used.

auto_neg/noauto_neg

is not supported

by some older cards. See

auto_neg / noauto_neg.

(page )

overlap/nooverlap

Configures the

and

memory hole to be overlapped. This enables in-line forwarding

without copying the data across the memory holes.

Example

dagconfig overlap
dagconfig nooverlap

Note:

This option is only applicable on firmware images containing TX.

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды