Endace DAG 5.2X Скачать руководство пользователя

Страница: 25 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

dagconfig tokens explained

Setting up the DAG card

Configuring the 10/100 mbps DAG 7.5G4 card

Use the supported copper SFP modules.

See

Pluggable Copper Transceivers.

(page )

Use Cat 5 or 6 cables.

Half duplex not supported.

Use the latest DAG software – 3.2.0 or greater.

Know the line rate prior to configuring DAG card.

Configure the cards as follows:

•

For 10 mbps noauto_neg, type:

dagconfig auto_neg 10 10

•

For 100 mbps noauto_neg, type:

dagconfig auto_neg 100 100

Note:

You must set the Switch to the same settings as the DAG card to ensure they

communicate correctly.

auto-neg/noauto-neg

is the same as

nic/nonic

10/100/1000

Set one of the following modes of operation:

•

Set 10BaseT mode, 10Mbps

•

Set 100BaseTX mode, 100Mbps

•

Set 1000BaseTX mode, 1000Mbps

Example

dagconfig 10

dagconfig 100

dagconfig 1000

align64

Sets the packets to be all generated as multiples of 8 bytes, 64-bit aligned, (

align64

) before

being received by the host. Not a configurable option.

auto_neg / noauto_neg

Note:

From DAG software 3.1.0 onwards

nic/nonic

is replaced by

auto_neg/noauto_neg

Both options are valid and still can be used.

auto_neg/noauto_neg

is not supported

by some older cards.

For Ethernet only. The DAG 7.5G4 card operates in either

“auto_neg”

“noauto_neg

” mode.

auto_neg

mode you must connect the DAG 7.5G4 card directly to a Ethernet switch or card

with a full-duplex cable, in which case the DAG 7.5G4 card will perform Ethernet auto-

negotiation.
The

noauto_neg

mode is intended for use with optical fiber splitters. In this mode you must

connect the receive socket of the DAG port to the output of an optical splitter inserted into a

network link between two other devices. The transmit socket of the DAG should be

unconnected.
In

noauto_neg

mode, Ethernet auto-negotiation is not performed. This allows you to use one

splitter on each DAG receive port to monitor each direction of a full-duplex Ethernet link.

Example

dagconfig auto_neg

dagconfig noauto_neg

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды