Endace DAG 5.2X Скачать руководство пользователя

Страница: 26 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

buffer_size

The buffer size=

MB indicates that a total of

MB of memory have been allocated to the

DAG card in total. Memory allocation occurs when the

dagmem

driver is loaded at boot time.

See

EDM04-01 DAG Software Installation Guide

for details on how to allocate memory.

crc

Indicates that this DAG card is set to perform a Cyclic Redundancy Check (CRC) on the

receive stream.
Not configurable.

crc16/crc32/nocrc

Sets the Packet over SONET (PoS) checking to None, 16 or 32 bits. SONET only.

Example

dagconfig nocrc
dagconfig crc16
dagconfig crc32

default

The

default

command initializes the DAG card configuration and sets all settings to default

values. The command also resets the DAG card configuration back to its default state.

Note:

When you run

dagconfig -d0 default

the

dagclock

inputs and outputs are also reset

to defaults.

Example

dagconfig -d0 default

drop/nodrop

Determines if the DAG card's memory holes are de-coupled.
In

drop

mode, the memory holes are de-coupled. If the data rate on one memory hole slows,

the data rate on any other memory holes is not affected. The dropping of packets occurs at

the individual stream's burst manager.
In

nodrop

mode, the memory holes are coupled. The speed of the slowest memory hole

determines the overall speed of the data rate. The dropping of packets occurs at the port.

Example

dagconfig drop
dagconfig nodrop

dsm bypass

Indicates whether DSM Bypass mode is active or not on the DAG card. Applicable to DAG

cards with DSM.

For more information on this option, see

Configuring DSM.

(page )

enable/disable

Sets whether this DAG card captures data on the defined port (a or b).

Note:

DAG ports are enabled by default. You do not need to use

dagconfig

to enable the

card in order to begin capture unless you have previously disabled it.

Example

dagconfig -d0 enablea
dagconfig -d0 disablea
dagconfig -d0 enableb
dagconfig -d0 disableb

where "0" is the device number of the DAG card you wish to capture data from

Note:

On some firmware images changes to this option may not take effect.

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды